PIC16C505-04E/SL Microchip Technology, PIC16C505-04E/SL Datasheet - Page 27
![IC MCU OTP 1KX12 14SOIC](/photos/6/59/65933/150-14-soic_sml.jpg)
PIC16C505-04E/SL
Manufacturer Part Number
PIC16C505-04E/SL
Description
IC MCU OTP 1KX12 14SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Specifications of PIC16C505-04E/SL
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Peripherals
POR, WDT
Number Of I /o
11
Program Memory Size
1.5KB (1K x 12)
Program Memory Type
OTP
Ram Size
72 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
14-SOIC (3.9mm Width), 14-SOL
For Use With
309-1086 - ADAPTER 14-ZIF BD W/14-SO PLUGS309-1085 - ADAPTER 14-DIP BD W/2 14-SO PLUG309-1001 - ADAPTER 14-SOIC TO 14-DIP309-1000 - ADAPTER 14-SOIC TO 14-DIP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Connectivity
-
7.0
What sets a microcontroller apart from other
processors are special circuits to deal with the needs
of
microcontroller has a host of such features intended to
maximize system reliability, minimize cost through
elimination of external components, provide power
saving operating modes and offer code protection.
These features are:
• Oscillator selection
• Reset
• Watchdog Timer (WDT)
• SLEEP
• Code protection
• ID locations
• In-circuit Serial Programming
• Clock Out
REGISTER 7-1:
- Power-On Reset (POR)
- Device Reset Timer (DRT)
- Wake-up from SLEEP on pin change
1999 Microchip Technology Inc.
bit11
bit 11-6, 4: CP Code Protection bits
bit 5:
bit 3:
bit 2-0:
Note 1:
CP
real-time
2:
3:
SPECIAL FEATURES OF THE
CPU
CP
10
MCLRE: RB3/MCLR pin function select
1 = RB3/MCLR pin function is MCLR
0 = RB3/MCLR pin function is digital I/O, MCLR internally tied to V
WDTE: Watchdog timer enable bit
1 = WDT enabled
0 = WDT disabled
FOSC<1:0>: Oscillator Selection bits
111 = external RC oscillator/CLKOUT function on RB4/OSC2/CLKOUT pin
110 = external RC oscillator/RB4 function on RB4/OSC2/CLKOUT pin
101 = internal RC oscillator/CLKOUT function on RB4/OSC2/CLKOUT pin
100 = internal RC oscillator/RB4 function on RB4/OSC2/CLKOUT pin
011 = invalid selection
010 = HS oscillator
001 = XT oscillator
000 = LP oscillator
03FFh is always uncode protected on the PIC16C505. This location contains the
MOVLWxx calibration instruction for the INTRC.
Refer to the PIC16C505 Programming Specifications to determine how to access the con-
figuration word. This register is not user addressable during device operation.
All code protect bits must be written to the same value.
applications.
CP
9
CONFIGURATION WORD FOR PIC16C505
CP
8
The
CP
7
(1)(2)(3)
PIC16C505
CP
6
MCLRE
5
CP
4
The PIC16C505 has a Watchdog Timer, which can be
shut off only through configuration bit WDTE. It runs
off of its own RC oscillator for added reliability. If using
HS, XT or LP selectable oscillator options, there is
always an 18 ms (nominal) delay provided by the
Device Reset Timer (DRT), intended to keep the chip
in reset until the crystal oscillator is stable. If using
INTRC or EXTRC, there is an 18 ms delay only on V
power-up. With this timer on-chip, most applications
need no external reset circuitry.
The SLEEP mode is designed to offer a very low
current power-down mode. The user can wake-up
from SLEEP through a change on input pins or
through a Watchdog Timer time-out. Several oscillator
options are also made available to allow the part to fit
the application, including an internal 4 MHz oscillator.
The EXTRC oscillator option saves system cost while
the LP crystal option saves power. A set of
configuration bits are used to select various options.
7.1
The PIC16C505 configuration word consists of 12 bits.
Configuration bits can be programmed to select
various device configurations. Three bits are for the
selection of the oscillator type, one bit is the Watchdog
Timer enable bit, and one bit is the MCLR enable bit.
Seven bits are for code protection (Register 7-1).
WDTE FOSC2 FOSC1 FOSC0
3
DD
Configuration Bits
2
1
PIC16C505
bit0
Register:
Address
DS40192C-page 27
(2)
:
CONFIG
0FFFh
DD