ATTINY861A-MUR Atmel, ATTINY861A-MUR Datasheet - Page 169

• Manufacturer Part Number: ATTINY861A-MUR
• Description: MCU AVR 8KB FLASH 20MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY861A-MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.2.1
18.3
18.4
8197B–AVR–01/10
Signature Bytes
Calibration Byte
Latching of Fuses
Table 18-5.
Notes:
Note that fuse bits are locked if Lock Bit 1 (LB1) is programmed. Fuse bits should be pro-
grammed before lock bits. The status of fuse bits is not affected by chip erase.
Fuse bits can also be read by device firmware. See section
Software” on page
Fuse values are latched when the device enters programming mode and changes to fuse values
have no effect until the part leaves programming mode. This does not apply to the EESAVE
Fuse which will take effect once it is programmed. Fuses are also latched on power-up.
All Atmel microcontrollers have a three-byte signature code which identifies the device. This
code can be read in both serial and High-voltage Programming mode, also when the device is
locked. The three bytes reside in a separate address space. The signature bytes are given in
Table
Table 18-6.
The signature area has one byte of calibration data for the internal oscillator. This byte resides in
the high byte of address 0x000. During reset, this byte is automatically written into the OSCCAL
Register to ensure correct frequency of the calibrated oscillator.
Fuse Low Byte
CKDIV8
CKOUT
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
Parts
ATtiny261A
ATtiny461A
ATtiny861A
18-6.
1. See
2. Allows system clock to be output on pin. See
3. The default value results in maximum start-up time for the default clock source. See
4. The default setting results in internal oscillator @ 8.0 MHz. See
(2)
(1)
on page 28
details.
Fuse Low Byte
Device ID
“System Clock Prescaler” on page 31
164.
Bit No
for details.
7
6
5
4
3
2
1
0
Description
Divide clock by 8
Clock Output Enable
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
0x000
0x1E
0x1E
0x1E
Signature Bytes Address
for details.
“Clock Output Buffer” on page 32
0x001
0x91
0x92
0x93
“Reading Fuse and Lock Bits from
Default Value
0 (programmed)
1 (unprogrammed)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
0 (programmed)
Table 6-6 on page 28
0x002
0x0C
0x0D
0x08
(3)
(4)
(4)
(4)
for details.
(3)
(4)
Table 6-7
for
169