PIC16F883-E/SO Microchip Technology, PIC16F883-E/SO Datasheet - Page 5
![IC PIC MCU FLASH 4KX14 28-SOIC](/photos/6/59/65909/150-28-soic_sml.jpg)
PIC16F883-E/SO
Manufacturer Part Number
PIC16F883-E/SO
Description
IC PIC MCU FLASH 4KX14 28-SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.MCP1631RD-MCC2.pdf
(328 pages)
3.PIC16F882-ISS.pdf
(16 pages)
4.PIC16F882-ISS.pdf
(36 pages)
5.PIC16F883-ISO.pdf
(288 pages)
Specifications of PIC16F883-E/SO
Program Memory Type
FLASH
Program Memory Size
7KB (4K x 14)
Package / Case
28-SOIC (7.5mm Width)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
24
Eeprom Size
256 x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC16F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
MSSP/EUSART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
24
Number Of Timers
3
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM164120-3
Minimum Operating Temperature
- 40 C
On-chip Adc
11-ch x 10-bit
A/d Bit Size
10 bit
A/d Channels Available
11
Height
2.31 mm
Length
17.87 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2 V
Width
7.49 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP1631RD-MCC2 - REFERENCE DESIGN MCP1631HV
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
3. Module: Analog-To-Digital Converter
EXAMPLE 2:
© 2009 Microchip Technology Inc.
BANKSEL
MOVLW
MOVWF
MOVLW
MOVWF
Selecting the VP6 reference as the analog input
source
conversion after sampling another analog channel
with input voltages approximately greater than
3.6V can temporarily disturb the HFINTOSC
oscillator.
Work around
Select an ADC channel with input voltages lower
than 3.6V prior to selecting the VP6 reference
voltage input. Any analog channel can be used,
even if that channel is configured as a digital I/O
(configured as an output) that is driving the output
pin low. An alternative is to configure the CV
module to output a voltage less than 3.6V and then
selecting that analog channel CHS<3:0> = 1110
as the analog input source.
Affected Silicon Revisions
PIC16F882
PIC16F883/PIC16F884
PIC16F886/PIC16F887
A0
A0
A2
Note:
X
X
X
ADCON0
B’XX111001’
ADCON0
B’XX111101’
ADCON0
(CHS<3:0> = 1111)
(ADC) Module
This only occurs when selecting the
VP6 reference ADC channel using the
CHS<3:0> bits in the ADCON0
register and NOT during the start of an
actual ADC conversion using the
GO/DONE bit in the ADCON0 register.
AVOID DISTURBING THE
HFINTOSC OSCILLATOR
;
;Select ADC
;Channel CV
;Select ADC
;Channel VP6
for
REF
the
ADC
REF
4. Module: MSSP (SPI Master Mode)
With MSSP in SPI Master mode, F
Timer2/2 clock rate and CKE = 0, a write collision
may occur if SSPBUF is loaded immediately after
the transfer is complete. A delay may be required
after the MSSP Interrupt Flag bit, SSPIF, is set or
the Buffer Full bit, BF, is set and before writing
SSPBUF. If the delay is insufficiently short, a write
collision may occur as indicated by the WCOL bit
being set.
Work around
Add a software delay of one SCK period after
detecting the completed transfer and prior to
updating the SSPBUF contents. Verify the WCOL
bit is clear after writing SSPBUF. If the WCOL is
set, clear the bit in software and rewrite the
SSPBUF register.
Date Codes that pertain to this issue:
All engineering and production devices.
Affected Silicon Revisions
PIC16F882
PIC16F883/PIC16F884
PIC16F886/PIC16F887
A0
A0
A2
X
X
X
PIC16F88X
DS80302F-page 5
OSC
/64 or