PIC16F1933-I/SO Microchip Technology, PIC16F1933-I/SO Datasheet - Page 8

• Manufacturer Part Number: PIC16F1933-I/SO
• Description: IC MCU 8BIT FLASH 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1933-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART, MI2C, SPI
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F/LF1933
8. Module: Enhanced Capture Compare
8.1 Enhanced PWM
8.2 Enhanced PWM
DS80490F-page 8
When the PWM is configured for Full-Bridge mode
and the duty cycle is set to 0%, writing the
PxM<1:0> bits to change the direction has no
effect on PxA and PxC outputs.
On the A4 revision products only, ECCP1 no
longer exhibits this problem.
Work around
Increase the duty cycle to a value greater than 0%
before changing directions.
Affected Silicon Revisions
In PWM mode, when the duty cycle is set to 0%
and the STRxSYNC bit is set, writing the STRxA,
STRxB, STRxC and the STRxD bits to enable/
disable steering to port pins has no effect on the
outputs.
Work around
Increase the duty cycle to a value greater than 0%
before enabling/disabling steering to port pins.
Affected Silicon Revisions
A1
A1
X
X
A2
A2
X
X
PWM (ECCP)
A3
A3
X
X
A4
A4
X
X
9. Module: In-Circuit Serial Programming™
9.1 Bulk Erase Feature not available with Low-
10. Module: LDO
10.1 Minimum V
Note:
Note:
Voltage Programming mode
A bulk erase of the program Flash memory or data
memory cannot be executed in Low-Voltage
Programming mode.
Work around
Affected Silicon Revisions
The
PIC16F1933 devices is 3.5 volts for temperatures
above 85°C.
Work around
None.
Affected Silicon Revisions
A1
A1
X
X
Method 1: If ICSP Low-Voltage Program-
Method 2: Use
minimum
Only the bulk erase feature will erase
program or data memory if code or data
protection is enabled. Method 2 must be
used if code or data protection is enabled.
This issue only applies to the PIC16F1933
devices
temperature range. The PIC16LF1933
devices are not affected.
A2
A2
X
X
(ICSP™)
DD
A3
A3
X
X
above 85°C
ming mode is required, use row
erases to erase the program
memory, as described in the
Program/Verify mode section of
the Programming Specification.
Data memory must be over-writ-
ten with the desired values.
Programming mode if a bulk
erase is required.
operating
voltage
 2010 Microchip Technology Inc.
A4
A4
X
ICSP
in
required
the
High-Voltage
Extended
for
the