ATMEGA88V-10AUR Atmel, ATMEGA88V-10AUR Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATMEGA88V-10AUR
Manufacturer Part Number
ATMEGA88V-10AUR
Description
MCU AVR 8K FLASH 10MHZ 32TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet
1.ATMEGA48-20AU.pdf
(35 pages)
Specifications of ATMEGA88V-10AUR
Core Processor
AVR
Core Size
8-Bit
Speed
10MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA88V-10AUR
Manufacturer:
Atmel
Quantity:
1 991
8.2
8.2.1
8.2.2
8.2.3
2545SS–AVR–07/10
Errata ATmega88
Rev. D
Rev. B/C
Rev. A
The revision letter in this section refers to the revision of the ATmega88 device.
•
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
Not sampled.
•
•
•
1. Writing to EEPROM does not work at low operating voltages
2. Part may hang in reset
Interrupts may be lost when writing the timer registers in the asynchronous timer
Writing to EEPROM does not work at low Operating Voltages
Part may hang in reset
Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
Writing to the EEPROM does not work at low voltages.
Problem Fix/Workaround
Do not write the EEPROM at voltages below 4.5 Volts.
This will be corrected in rev. B.
Some parts may get stuck in a reset state when a reset signal is applied when the internal
reset state-machine is in a specific state. The internal reset state-machine is in this state for
approximately 10 ns immediately before the part wakes up after a reset, and in a 10 ns win-
dow when altering the system clock prescaler. The problem is most often seen during In-
System Programming of the device. There are theoretical possibilities of this happening also
in run-mode. The following three cases can trigger the device to get stuck in a reset-state:
- Two succeeding resets are applied where the second reset occurs in the 10ns window
before the device is out of the reset-state caused by the first reset.
- A reset is applied in a 10 ns window while the system clock prescaler value is updated by
software.
- Leaving SPI-programming mode generates an internal reset signal that can trigger this
case.
The two first cases can occur during normal operating mode, while the last case occurs only
during programming of the device.
ATmega48/88/168
25