PIC16F818-I/P Microchip Technology, PIC16F818-I/P Datasheet - Page 3

• Manufacturer Part Number: PIC16F818-I/P
• Description: IC MCU FLASH 1KX14 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F818-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: I2C/SPI/SSP
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2. Module: Internal RC Oscillator
3. Module: PORTB Pull-ups
© 2005 Microchip Technology Inc.
When any one of the seven INTOSC frequencies
is enabled by the following conditions, it is possible
for the oscillator to overshoot the selected
frequency.:
1. A clock switch from INTRC (31 kHz) to an
2. Exit from Sleep mode with the IRCF bits
If the selected frequency is 8 MHz, then the
Voltage versus Frequency specification of the
device may be violated.
Work around
When it is required for the application to run at
8 MHz, it is recommended that the application
does not start executing code at 8 MHz until the
60ms firmware delay (see issue 1) has completed.
During the 60 ms settling period, the application
can execute code up to 4 MHz. Upon completion
of the 60 ms firmware delay, the 8 MHz can be
selected via the IRCF bits.
Date Codes that pertain to this issue:
All date codes.
When RBPU = 0 (OPTION register), the PORTB
weak pull-ups will not be disabled by the input
functions of the SSP and/or CCP (Capture mode)
module as indicated by the RB1:RB5 I/O block
diagrams in Section 5.0 “I/O Ports”.
Work around
1. If the SSP and/or CCP (Capture mode) module
OR
2. If the SSP and/or CCP (Capture mode) module
Date Codes that pertain to this issue:
All date codes.
INTOSC (125 kHz-8 MHz) frequency via the
IRCF bits (OSCCON register).
already configured for an INTOSC frequency.
is enabled, do not enable the PORTB weak
pull-ups and use external pull-up resistors.
and PORTB pull-ups are enabled, then evalu-
ate the functionality of the SSP (I
or CCP (Capture mode) module to ensure
proper operation within your application.
2
C™/SPI™)
4. Module: PORTB
5. Module: PORTB Interrupts
A delay of 1 T
modifies the contents of PORTB simultaneously
occurs when any of the following modules (if
enabled) executes an operation that effects the
signals on their respective PORTB I/O pins.
CCP Module:
PWM Mode (CCP1CON<3:0> = 11xx)
When CCP1CON<5:4> bits = 10, the PWM output
signal will be delayed by 1 T
instruction to modify the contents of PORTB is
executed.
SSP Module:
SPI Slave Modes (SSPCON<3:0> = 0100 and 0101)
Clock signal is derived from an external source.
Transmission of data (SDO pin) will be delayed by
1 T
of PORTB is executed. Reception of data is not
affected.
Work around
None
Date Codes that pertain to this issue:
All date codes.
When the PORTB interrupt-on-change feature and
a PORTB peripheral are enabled simultaneously,
the PORTB peripheral input signal’s rising and
falling edges will trigger an interrupt-on-change
event. This is due to the interrupt-on-change
feature not being disabled on the respective pin for
that peripheral when it is enabled.
The affected pins and peripheral signals on
PORTB are RB4: SCK and SCL, RB5: SS and
RB6: T1CKI. The functionality of T1OSI (RB7) and
T1OSO (RB6) is not affected by this issue.
Work around
None.
OSC
when an instruction to modify the contents
PIC16F818/819
OSC
will occur if an instruction that
DS80212C-page 3
OSC
when an