PIC16F1947-I/PT Microchip Technology, PIC16F1947-I/PT Datasheet - Page 244

• Manufacturer Part Number: PIC16F1947-I/PT
• Description: IC MCU 8BIT FLASH 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1947-I/PT

• Core Size: 8-Bit
• Program Memory Size: 28KB (16K x 14)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC16F
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1024Byte
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: EUSART, I2C, SPI
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 17 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F/LF1946/47
The I
features:
• Master mode
• Slave mode
• Byte NACKing (Slave mode)
• Limited Multi-master support
• 7-bit and 10-bit addressing
• Start and Stop interrupts
• Interrupt masking
• Clock stretching
• Bus collision detection
• General call address matching
• Address masking
• Address Hold and Data Hold modes
• Selectable SDAx hold times
Figure 24-2
ule in Master mode.
interface module in Slave mode.
FIGURE 24-2:
DS41414B-page 244
2
C interface supports the following modes and
SDAx
SCLx
is a block diagram of the I
Figure 24-3
MSSPX BLOCK DIAGRAM (I
SDAx in
is a diagram of the I
SCLx in
Bus Collision
2
C interface mod-
Read
MSb
Generate (SSPxCON2)
Address Match detect
Preliminary
Write collision detect
2
end of XMIT/RCV
Start bit, Stop bit,
State counter for
Clock arbitration
C
Start bit detect,
Stop bit detect
Acknowledge
SSPxBUF
SSPxSR
2
C™ MASTER MODE)
The PIC16F1947 has two MSSP modules, MSSP1 and
MSSP2, each module operating independently from
the other.
LSb
Note 1: In devices with more than one MSSP
Write
Clock
Shift
data bus
Internal
2: Throughout this section, generic refer-
Set/Reset: S, P, SSPxSTAT, WCOL, SSPxOV
Reset SEN, PEN (SSPxCON2)
Set SSPxIF, BCLxIF
module, it is very important to pay close
attention to SSPxCONx register names.
SSP1CON1 and SSP1CON2 registers
control different operational aspects of
the same module, while SSP1CON1 and
SSP2CON1 control the same features for
two different modules.
ences to an MSSP module in any of its
operating modes may be interpreted as
being equally applicable to MSSP1 or
MSSP2. Register names, module I/O sig-
nals, and bit names may use the generic
designator ‘x’ to indicate the use of a
numeral to distinguish a particular module
when required.
 2010 Microchip Technology Inc.
[SSPxM 3:0]
Baud rate
generator
(SSPxADD)