ATMEGA165P-16MN Atmel, ATMEGA165P-16MN Datasheet - Page 298

• Manufacturer Part Number: ATMEGA165P-16MN
• Description: MCU AVR 16KB FLASH 16MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA165P-16MN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Processor Series: ATMEGA16x
• Core: AVR8
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T
Note:
8019K–AVR–11/10
A
Symbol
I
V
I
t
CC
ACLK
ACPD
ACIO
= -40⋅C to 85⋅C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (20 mA at V
5. All bits set in the “Power Reduction Register” on page 34.
6. Typical values at 25 ⋅C. Maximum values are characterized values and not test limits in production.
at V
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
at V
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.
3] The sum of all IOH, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.
4] The sum of all IOH, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.
5] The sum of all IOH, for ports F0 - F7, should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Power Supply Current
Power-save mode
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
CC
= 5V, 5 mA at V
= 5V, 5 mA at V
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
(6)
(6)
CC
CC
(5)
= 3V for all other ports) under steady state conditions (non-transient), the following must be
= 3V for all other ports) under steady state conditions (non-transient), the following must be
WDT disabled, V
V
V
V
Condition
Active 1 MHz, V
Active 4 MHz, V
Active 8 MHz, V
Idle 1 MHz, V
Idle 4 MHz, V
Idle 8 MHz, V
32 kHz TOSC enabled,
V
32 kHz TOSC enabled,
V
WDT enabled, V
V
V
V
CC
CC
CC
in
CC
in
CC
CC
= V
= V
= 1.8V
= 3V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
= 2V
= 3V
= 5V
= 3V
= 3V
Min.
-50
CC
CC
= 5V, 10 mA at V
= 5V, 10 mA at V
Typ.
0.35
0.55
<10
750
500
2.3
8.4
0.1
0.7
3.0
0.8
0.2
6
CC
CC
ATmega165P
Max.
0.44
= 3V for Port B and 10 mA
2.5
9.5
0.2
0.8
3.3
1.6
2.6
10
40
50
= 3V for Port B and 10mA
2
Units
mA
mV
µA
nA
ns
298