PIC24FJ64GB004-I/PT Microchip Technology, PIC24FJ64GB004-I/PT Datasheet - Page 21
![IC MCU 16BIT 64KB FLASH 44TQFP](/photos/6/82/68251/c04-076_pt_sml.jpg)
PIC24FJ64GB004-I/PT
Manufacturer Part Number
PIC24FJ64GB004-I/PT
Description
IC MCU 16BIT 64KB FLASH 44TQFP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 24Fr
Datasheets
1.PIC24FJ32GA102-ISP.pdf
(48 pages)
2.PIC24FJ32GB002-ISO.pdf
(352 pages)
3.PIC24FJ32GB002-ISO.pdf
(12 pages)
4.PIC24FJ32GB002-ISO.pdf
(342 pages)
Specifications of PIC24FJ64GB004-I/PT
Core Size
16-Bit
Program Memory Size
64KB (22K x 24)
Core Processor
PIC
Speed
32MHz
Connectivity
I²C, IrDA, SPI, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
33
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 13x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-TQFP, 44-VQFP
Controller Family/series
PIC24
Ram Memory Size
8KB
Cpu Speed
32MHz
No. Of Timers
5
Interface
I2C, LIN, SPI, UART, USB
No. Of Pwm Channels
5
Embedded Interface Type
I2C, LIN, SPI, UART, USB
Rohs Compliant
Yes
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8 KB
Interface Type
I2C, IrDA, SPI, UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
33
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 13 Channel
A/d Bit Size
10 bit
A/d Channels Available
13
Height
1 mm
Length
10 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2 V
Width
10 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARD
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ64GB004-I/PT
Manufacturer:
NEC
Quantity:
201
Company:
Part Number:
PIC24FJ64GB004-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC24FJ64GB004-I/PT
Manufacturer:
MICROHCIP
Quantity:
20 000
2.4
The on-chip voltage regulator enable/disable pin
(ENVREG or DISVREG, depending on the device
family) must always be connected directly to either a
supply voltage or to ground. The particular connection
is determined by whether or not the regulator is to be
used:
• For ENVREG, tie to V
• For DISVREG, tie to ground to enable the
Refer to Section 26.2 “On-Chip Voltage Regulator”
for details on connecting and using the on-chip
regulator.
When the regulator is enabled, a low-ESR (<5Ω)
capacitor is required on the V
stabilize the voltage regulator output voltage. The
V
must use a capacitor of 10 μF connected to ground. The
type can be ceramic or tantalum. A suitable example is
the Murata GRM21BF50J106ZE01 (10 μF, 6.3V), or
equivalent. Designers may use Figure 2-3 to evaluate
ESR equivalence of candidate devices.
The placement of this capacitor should be close to
V
length not exceed 0.25 inch (6 mm). Refer to
Section 29.0
additional information.
When the regulator is disabled, the V
must be tied to a voltage supply at the V
Refer to Section 29.0 “Electrical Characteristics” for
information on V
FIGURE 2-3:
© 2009 Microchip Technology Inc.
CAP
CAP
Note:
or to ground to disable the regulator
regulator, or to V
0.001
Note:
0.01
/V
0.1
/V
10
1
DDCORE
DDCORE
0.01
Voltage Regulator Pins
(ENVREG/DISVREG and
V
CAP
This section applies only to PIC24FJ
devices with an on-chip voltage regulator.
Data for Murata GRM21BF50J106ZE01 shown.
Measurements at 25°C, 0V DC bias.
. It is recommended that the trace
0.1
/V
pin must not be connected to V
“Electrical
DD
DDCORE
DD
and V
Frequency (MHz)
to disable the regulator
FREQUENCY vs. ESR
PERFORMANCE FOR
SUGGESTED V
1
DD
DDCORE
to enable the regulator,
)
10
Characteristics”
CAP
.
100
/V
CAP
DDCORE
DDCORE
/V
CAP
1000 10,000
DDCORE
DD
pin to
level.
, and
PIC24FJ64GB004 FAMILY
Preliminary
pin
for
2.5
The PGECx and PGEDx pins are used for In-Circuit
Serial Programming (ICSP) and debugging purposes.
It is recommended to keep the trace length between
the ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100Ω.
Pull-up resistors, series diodes and capacitors on the
PGECx and PGEDx pins are not recommended as they
will interfere with the programmer/debugger communi-
cations to the device. If such discrete components are
an application requirement, they should be removed
from the circuit during programming and debugging.
Alternatively, refer to the AC/DC characteristics and
timing requirements information in the respective
device Flash programming specification for information
on capacitive loading limits and pin input voltage high
(V
For device emulation, ensure that the “Communication
Channel
programmed into the device matches the physical
connections for the ICSP to MPLAB
ICD 3 or MPLAB REAL ICE™ emulator.
For more information on the ICD 2, ICD 3 and REAL
ICE emulator connection requirements, refer to the
following documents that are available on the
Microchip web site.
• “MPLAB
• “Using MPLAB
• “MPLAB
• “Using MPLAB
• “MPLAB
• “MPLAB
• “Using MPLAB
IH
Guide” (DS51331)
Guide” (DS51616)
(poster) (DS51749)
) and input low (V
ICSP Pins
®
®
®
®
Select”
ICD 2 In-Circuit Debugger User’s
ICD 2 Design Advisory” (DS51566)
ICD 3 Design Advisory” (DS51764)
REAL ICE™ In-Circuit Emulator User’s
®
®
®
ICD 2” (poster) (DS51265)
ICD 3” (poster) (DS51765)
REAL ICE™ In-Circuit Emulator”
IL
(i.e.,
) requirements.
PGECx/PGEDx
DS39940C-page 19
®
ICD 2, MPLAB
pins)