PIC24HJ128GP506A-I/PT Microchip Technology, PIC24HJ128GP506A-I/PT Datasheet - Page 32
![IC PIC MCU FLASH 128KB 64-TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
PIC24HJ128GP506A-I/PT
Manufacturer Part Number
PIC24HJ128GP506A-I/PT
Description
IC PIC MCU FLASH 128KB 64-TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Hr
Datasheets
1.PIC24HJ12GP201-ISO.pdf
(84 pages)
2.PIC24HJ64GP206A-IMR.pdf
(304 pages)
3.PIC24HJ64GP206A-IMR.pdf
(10 pages)
Specifications of PIC24HJ128GP506A-I/PT
Program Memory Type
FLASH
Program Memory Size
128KB (43K x 24)
Package / Case
64-TFQFP
Core Processor
PIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
53
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 18x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24HJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8192 B
Interface Type
SPI, I2C, UART
Maximum Clock Frequency
7.37 MHz
Number Of Timers
13
Operating Supply Voltage
3 V to 3.6 V
Maximum Operating Temperature
+ 140 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005
Minimum Operating Temperature
- 40 C
On-chip Adc
16 bit, 8 Channel
Controller Family/series
PIC24
No. Of I/o's
53
Ram Memory Size
8KB
Cpu Speed
40MHz
No. Of Timers
9
Embedded Interface Type
CAN, I2C, SPI, UART
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24HJ128GP506A-I/PT
Manufacturer:
MICROCHIP
Quantity:
258
Company:
Part Number:
PIC24HJ128GP506A-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC24HJ128GP506A-I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
5.0
ICSP mode is a special programming protocol that
allows you to read and write to dsPIC33F/PIC24H
device family memory. The ICSP mode is the most
direct method used to program the device; however,
note that Enhanced ICSP is faster. ICSP mode also
has the ability to read the contents of executive
memory to determine if the programming executive is
present. This capability is accomplished by applying
control codes and instructions serially to the device
using pins PGCx and PGDx.
In ICSP mode, the system clock is taken from the
PGCx pin, regardless of the device’s oscillator Config-
uration bits. All instructions are shifted serially into an
internal buffer, then loaded into the instruction register
and executed. No program fetching occurs from inter-
nal memory. Instructions are fed in 24 bits at a time.
PGDx is used to shift data in, and PGCx is used as both
the serial shift clock and the CPU execution clock.
DS70152H-page 32
Note:
Note:
DEVICE PROGRAMMING – ICSP
Any development tool that modifies the con-
figuration memory on dsPIC33FJ06GS101/
102/202,
504, dsPIC33FJ32GS406/606/608/610 and
dsPIC33FJ64GS406/606/608/610 devices
must take care to preserve the data con-
tained in the last six words of program mem-
ory. Refer to
Calibration
information.
During ICSP operation, the operating
frequency of PGCx must not exceed
5 MHz.
Appendix C: “Diagnostic and
dsPIC33FJ16GS402/404/502/
Registers”
for
more
5.1
Figure 5-1
programming process. After entering ICSP mode, the
first action is to Bulk Erase the device. Next, the code
memory is programmed, followed by the device
Configuration registers. Code memory (including the
Configuration registers) is then verified to ensure that
programming was successful. Then, program the
code-protect Configuration bits, if required.
FIGURE 5-1:
Overview of the Programming
Process
illustrates the high-level overview of the
Program Configuration Bits
Verify Configuration Bits
Program Memory
Verify Program
Enter ICSP™
Perform Bulk
Exit ICSP
HIGH-LEVEL ICSP™
PROGRAMMING FLOW
© 2010 Microchip Technology Inc.
Erase
Start
End