PIC14000T-04/SS Microchip Technology, PIC14000T-04/SS Datasheet - Page 85

• Manufacturer Part Number: PIC14000T-04/SS
• Description: IC MCU OTP 4KX14 A/D 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 14r

Specifications of PIC14000T-04/SS

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 20
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 6 V
• Data Converters: Slope A/D
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SSOP
• Processor Series: PIC14000
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 192 B
• Interface Type: SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1
• Operating Supply Voltage: 2.7 V to 6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• On-chip Adc: 14 bit
• For Use With: 309-1025 - ADAPTER 28-SSOP TO 28-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

10.7
The watchdog timer is realized as a free running
on-chip RC oscillator which does not require any
external components. This RC oscillator is separate
from the IN oscillator used to generate the CPU and
A/D clocks. That means that the WDT will run even if
the clock has been stopped, for example, by execution
of a SLEEP instruction. Refer to Section 10.8.1 for more
information.
During normal operation, a WDT time-out generates a
device RESET. If the device is in SLEEP mode, a WDT
time-out causes the device to wake-up and continue
with normal operation.
FIGURE 10-11: WATCHDOG TIMER BLOCK DIAGRAM (WITH TIMER0)
1996 Microchip Technology Inc.
RC3/T0CKI
pin
HIBERNATE
Watchdog Timer (WDT)
Oscillator
Enable
18 mS
Timer
Local
T0SE
F
WDT
Enable Bit
OSC
/4
Watchdog Timer
T0CS
0
1
PSA
0
1
Note: T0CS, T0SE, PSA, PS2:PS0 correspond to (OPTION<5:0>).
Preliminary
8-bit Counter
Timer0
8-to-1 MUX
1
8
0
Time-out
The
programming the configuration bit WDTE as a ‘0’. Its
oscillator can be shut down to conserve battery power
by
Section 10.8.3 for more information on HIBERNATE
mode.
A block diagram of the watchdog timer is shown in
Figure 10-11. It should be noted that a RESET
generated by the WDT time-out does not drive MCLR
low.
PSA
WDT
1
0
CAUTION: Beware of disabling WDT if software
PSout
entering
WDT
(2 cycle delay)
PSA
Sync with
3
Internal
Postscaler
Prescaler/
clocks
can
routines require exiting based on WDT
reset. For example, the MCU will not
exit HIBERNATE mode based on WDT
reset.
PS2:PS0
HIBERNATE
be
PSout
permanently
PIC14000
Data bus
TMR0
Mode.
Set T0IF
Interrupt on
Overflow
DS40122B-page 85
8
disabled
Refer
by
to