PIC24HJ256GP610A-I/PF Microchip Technology, PIC24HJ256GP610A-I/PF Datasheet - Page 153

• Manufacturer Part Number: PIC24HJ256GP610A-I/PF
• Description: IC MCU 16BIT 256KB FLASH 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ256GP610A-I/PF

• Program Memory Type: FLASH
• Program Memory Size: 256KB (85.5K x 24)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: CAN/I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 9
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (32-ch x 12-bit)
• Controller Family/series: PIC24
• Ram Memory Size: 16KB
• Cpu Speed: 40MIPS
• No. Of Timers: 9
• Embedded Interface Type: CAN, I2C, LIN, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15.0
The output compare module can select either Timer2 or
Timer3 for its time base. The module compares the
value of the timer with the value of one or two Compare
registers depending on the operating mode selected.
FIGURE 15-1:
© 2009 Microchip Technology Inc.
Note:
Note 1:
OUTPUT COMPARE
This data sheet summarizes the features
of the PIC24HJXXXGPX06/X08/X10 fam-
ilies of devices. It is not intended to be a
comprehensive
complement the information in this data
sheet, refer to the “PIC24H Family
Reference Manual”, Section 13. “Output
Compare” (DS70247), which is available
on
(www.microchip.com).
2: The OCFA pin controls OC1 through OC4. The OCFB pin controls OC5 through OC8.
An ‘x’ in a signal, register or bit name denotes the number of the output compare channels.
the
OUTPUT COMPARE MODULE BLOCK DIAGRAM
16
TMR2
OCxRS
Comparator
Microchip
OCxR
0
reference
TMR3
(1)
(1)
1
16
OCTSEL
web
source.
PIC24HJXXXGPX06/X08/X10
Rollover Rollover
site
TMR2
To
0
TMR3
1
The state of the output pin changes when the timer
value matches the Compare register value. The output
compare module generates either a single output
pulse, or a sequence of output pulses, by changing the
state of the output pin on the compare match events.
The output compare module can also generate
interrupts on compare match events.
The output compare module has multiple operating
modes:
• Active-Low One-Shot mode
• Active-High One-Shot mode
• Toggle mode
• Delayed One-Shot mode
• Continuous Pulse mode
• PWM mode without Fault Protection
• PWM mode with Fault Protection
Mode Select
OCM<2:0>
Output
3
Logic
Set Flag bit
OCxIF
(1)
R
S
Q
Output Enable
DS70175H-page 151
OCx
OCFA
or
OCFB
(1)
(2)