PIC32MX695F512L-80I/PT Microchip Technology, PIC32MX695F512L-80I/PT Datasheet - Page 17

• Manufacturer Part Number: PIC32MX695F512L-80I/PT
• Description: IC MCU 32BIT 512KB FLASH 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX695F512L-80I/PT

• Core Size: 32-Bit
• Program Memory Size: 512KB (512K x 8)
• Core Processor: MIPS32® M4K™
• Speed: 80MHz
• Connectivity: Ethernet, I²C, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Type: FLASH
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Controller Family/series: PIC32
• Ram Memory Size: 128KB
• Cpu Speed: 80MHz
• No. Of Timers: 5
• Interface: I2C, SPI, UART, USB
• No. Of Pwm Channels: 5
• Embedded Interface Type: I2C, SPI, UART, USB
• Rohs Compliant: Yes
• Processor Series: PIC32MX6xx
• Core: MIPS
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

8.0
Before a device can be programmed, the programmer
must check the status of the device to ensure that it is
ready to receive information.
FIGURE 8-1:
© 2010 Microchip Technology Inc.
CHECK DEVICE STATUS
statusVal = XferData (MCHP_STATUS)
No
SendCommand (MTAP_COMMAND)
SendCommand (MTAP_SW_MTAP)
SetMode (6’b011111)
Set MCLR low
CFGRDY = 1
CHECK DEVICE STATUS
FCBUSY = 0
Done
Yes
4-Wire
8.1
Four-wire JTAG programming is a Mission mode
operation and therefore the setup sequence to begin
programing should be done while asserting MCLR.
Holding the device in Reset prevents the processor
from executing instructions or driving ports.
The following steps are required to check the device
status using the 4-wire interface:
1.
2.
3.
4.
5.
6.
8.2
The following steps are required to check the device
status using the 2-wire interface:
1.
2.
3.
4.
5.
Note:
Set MCLR pin low.
SetMode (6’b011111) to force the Chip TAP
controller into Run Test/Idle state.
SendCommand (MTAP_SW_MTAP).
SendCommand (MTAP_COMMAND).
statusVal = XferData (MCHP_STATUS).
If CFGRDY (statusVal<3>) is not ‘1’ and
FCBUSY (statusVal<2>) is not ‘0’ GOTO step 5.
SetMode (6’b011111) to force the Chip TAP
controller into Run Test/Idle state.
SendCommand (MTAP_SW_MTAP).
SendCommand (MTAP_COMMAND).
statusVal = XferData (MCHP_STATUS).
If CFGRDY (statusVal<3>) is not ‘1’ and
FCBUSY (statusVal<2>) is not ‘0’, GOTO
step 4.
4-Wire Interface
2-Wire Interface
If CFGRDY and FCBUSY do not come to
the proper state within 10 ms, the
sequence may have been executed wrong
or the device is damaged.
PIC32MX
DS61145G-page 17