ATMEGA640V-8AU Atmel, ATMEGA640V-8AU Datasheet - Page 32

• Manufacturer Part Number: ATMEGA640V-8AU
• Description: IC MCU AVR 64K FLASH 100-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA640V-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, JTAG, SPI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Controller Family/series: AVR MEGA
• No. Of I/o's: 86
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.11 ATmega2561 rev. C
10.12 ATmega2561 rev. B
10.13 ATmega2561 rev. A
2549MS–AVR–09/10
•
1. High current consumption in sleep mode
Not sampled.
•
•
•
•
•
•
1.
2. Part does not work under 2.4 volts
3. Incorrect ADC reading in differential mode
4. Internal ADC reference has too low value
High current consumption in sleep mode.
Non-Read-While-Write area of flash not functional.
Part does not work under 2.4 Volts.
Incorrect ADC reading in differential mode.
Internal ADC reference has too low value.
IN/OUT instructions may be executed twice when Stack is in external RAM.
EEPROM read from application code does not work in Lock Bit Mode 3.
If a pending interrupt cannot wake the part up from the selected sleep mode, the current
consumption will increase during sleep when executing the SLEEP instruction directly after
a SEI instruction.
Problem Fix/Workaround
Before entering sleep, interrupts not used to wake the part from the sleep mode should be
disabled.
The Non-Read-While-Write area of the flash is not working as expected. The problem is
related to the speed of the part when reading the flash of this area.
Problem Fix/Workaround
- Only use the first 248K of the flash.
- If boot functionality is needed, run the code in the Non-Read-While-Write area at maximum
1/4th of the maximum frequency of the device at any given voltage. This is done by writing
the CLKPR register before entering the boot section of the code.
The part does not execute code correctly below 2.4 volts.
Problem Fix/Workaround
Do not use the part at voltages below 2.4 volts.
The ADC has high noise in differential mode. It can give up to 7 LSB error.
Problem Fix/Workaround
Use only the 7 MSB of the result when using the ADC in differential mode.
The internal ADC reference has a value lower than specified.
Problem Fix/Workaround
- Use AVCC or external reference.
Non-Read-While-Write area of flash not functional
ATmega640/1280/1281/2560/2561
32