STM8S207C6T6TR STMicroelectronics, STM8S207C6T6TR Datasheet - Page 56

• Manufacturer Part Number: STM8S207C6T6TR
• Description: MCU 8BIT 32K MEMORY 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM8Sr

Specifications of STM8S207C6T6TR

• Mfg Application Notes: STM8S Getting Started
• Core Processor: STM8
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.95 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: STM8S20x
• Core: STM8
• Data Bus Width: 8 bit
• Data Ram Size: 6 KB
• Interface Type: CAN,12C,SPI,UART
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 2
• Operating Supply Voltage: 2.95 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWSTM8
• Development Tools By Supplier: STICE-SYS001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-10032 - EVAL KIT MOTOR CONTROL STM8S497-10031 - EVAL KIT TOUCH SENSING STM8S497-10592 - BOARD DAUGHTER FOR STM8S207/8497-10593 - KIT STARTER FOR STM8S207/8 SER497-8506 - BOARD EVAL FOR STM8S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Electrical characteristics
56/105
Table 16.
1. Data based on characterization results, not tested in production.
2. All power (V
3. I/O pins used simultaneously for high current source/sink must be uniformly spaced around the package
4. I
5. Negative injection disturbs the analog performance of the device. See note in
6. When several inputs are submitted to a current injection, the maximum
Table 17.
I
I
INJ(PIN)
external supply.
between the V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
characteristics on page
positive and negative injected currents (instantaneous values). These results are based on
characterization with
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
I
VDD
VSS
I
T
IO
IO
STG
T
(4)(5)
J
must never be exceeded. This is implicitly insured if V
(4)
Current characteristics
Thermal characteristics
DD
DDIO
, V
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Total output current sourced (sum of all I/O and control pins)
for devices with two V
Total output current sourced (sum of all I/O and control pins)
for devices with one V
Total output current sunk (sum of all I/O and control pins) for
devices with two V
Total output current sunk (sum of all I/O and control pins) for
devices with one V
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DDIO
/V
SSIO

, V
I
INJ(PIN)
84.
IN
DDA
>V
pins.
DD
) and ground (V
Maximum junction temperature
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Storage temperature range
Doc ID 14733 Rev 11
SSIO
DD
SSIO
SS
DDIO
power lines (source)
DDIO
Ratings
pins
ground lines (sink)
pin
SS
Ratings
, V
(3)
pins
pin
(3)
SSIO
(3)
(3)
(6)
, V
SSA
) pins must always be connected to the
IN
IN
maximum must always be respected
maximum is respected. If V
(2)
(2)

I
IN
INJ(PIN)
STM8S207xx, STM8S208xx
<V
INJ(PIN)
(6)
SS
Section 10.3.10: 10-bit ADC
. For true open-drain pads,
is the absolute sum of the
-65 to 150
value. A positive
Value
150
Max.
±20
200
100
160
60
60
20
20
80
±4
±4
±4
IN
(1)
maximum
Unit
Unit
°C
mA