ST72F63BK6M1 STMicroelectronics, ST72F63BK6M1 Datasheet - Page 93

• Manufacturer Part Number: ST72F63BK6M1
• Description: MCU 8BIT LS USB 32KB FLSH 34SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F63BK6M1

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 19
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 34-SOIC (7.5mm Width)
• Processor Series: ST72F6x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 19
• Number Of Timers: 1
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MDTU3-EPB/US, ST72F63B-SK/RAIS, ST7MDTU3-EMU3, STX-RLINK
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit, 8 Channel / 8 bit, 12 Channel
• For Use With: 497-8428 - BOARD EVAL CHARGER ST7260/L6924D497-5521 - EVAL BOARD LOW SPEED USB497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5625-5

ST7263Bxx
Control register 2 (SCICR2)
Reset value: 0000 0000 (00h)
TIE
7
TCIE
7 TIE Transmitter interrupt enable.
6 TCIE Transmission complete interrupt enable
5 RIE Receiver interrupt enable.
4 ILIE Idle line interrupt enable.
3 TE Transmitter enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever TDRE=1 in the SCISR register
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever TC=1 in the SCISR register
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever OR=1 or RDRF=1 in the SCISR
register
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever IDLE=1 in the SCISR register.
This bit enables the transmitter. It is set and cleared by software.
0: Transmitter is disabled
1: Transmitter is enabled
Note: During transmission, a “0” pulse on the TE bit (“0” followed by “1”)
Caution: The TDO pin is free for general purpose I/O only when the TE and
RIE
sends a preamble (idle line) after the current word.
When TE is set there is a 1 bit-time delay before the transmission
starts.
Doc ID 7516 Rev 8
RE bits are both cleared (or if TE is never set).
ILIE
Read/write
TE
RE
On-chip peripherals
RWU
SBK
0
93/186