C8051F019-GQR Silicon Laboratories Inc, C8051F019-GQR Datasheet - Page 81
![IC 8051 MCU 16K FLASH 48TQFP](/photos/15/92/159280/tqfp-48_sml.jpg)
C8051F019-GQR
Manufacturer Part Number
C8051F019-GQR
Description
IC 8051 MCU 16K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F018r
Specifications of C8051F019-GQR
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP, 48-VQFP
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C, SMBus, SPI, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
16
Number Of Timers
4 bit
Operating Supply Voltage
2.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F005DK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F019-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
12. OSCILLATOR
Each MCU includes an internal oscillator and an external oscillator drive circuit, either of which can generate the
system clock. The MCUs boot from the internal oscillator after any reset. The internal oscillator starts up instantly.
It can be enabled/disabled and its frequency can be changed using the Internal Oscillator Control Register
(OSCICN) as shown in Figure 12.2. The internal oscillator’s electrical specifications are given in Table 12.1.
Both oscillators are disabled when the /RST pin is held low. The MCUs can run from the internal oscillator or
external oscillator, and switch between the two at will using the CLKSL bit in the OSCICN Register. The external
oscillator requires an external resonator, parallel-mode crystal, capacitor, or RC network connected to the
XTAL1/XTAL2 pins (see Figure 12.1). The oscillator circuit must be configured for one of these sources in the
OSCXCN register. An external CMOS clock can also provide the system clock via overdriving the XTAL1 pin.
The XTAL1 and XTAL2 pins are 3.6V (not 5V) tolerant. The external oscillator can be left enabled and running
even when the MCU has switched to using the internal oscillator.
81
opt. 4
XTAL1
C8051F018
C8051F019
opt. 3
XTAL1
XTAL2
AV+
opt. 2
XTAL1
opt. 1
XTAL1
XTAL2
AGND
Figure 12.1. Oscillator Diagram
VDD
AV+
Circuit
Input
OSCXCN
Internal Clock
OSCICN
Generator
EN
OSC
Rev. 1.2
SYSCLK