PIC16C72-04E/SP Microchip Technology, PIC16C72-04E/SP Datasheet - Page 106
![IC MCU OTP 2KX14 A/D PWM 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC16C72-04E/SP
Manufacturer Part Number
PIC16C72-04E/SP
Description
IC MCU OTP 2KX14 A/D PWM 28DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C72-04SO.pdf
(289 pages)
4.PIC16C72-04SO.pdf
(125 pages)
5.PIC16C72-04SO.pdf
(8 pages)
Specifications of PIC16C72-04E/SP
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Connectivity
I²C, SPI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
28-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- PIC16F616T-ISL PDF datasheet
- PIC16F818-ISO PDF datasheet #2
- PIC16C72-04SO PDF datasheet #3
- PIC16C72-04SO PDF datasheet #4
- PIC16C72-04SO PDF datasheet #5
- Current page: 106 of 289
- Download datasheet (3Mb)
PIC16C7X
12.2
In this mode, the USART uses standard nonreturn-to-
zero (NRZ) format (one start bit, eight or nine data bits
and one stop bit). The most common data format is
8-bits. An on-chip dedicated 8-bit baud rate generator
can be used to derive standard baud rate frequencies
from the oscillator. The USART transmits and receives
the LSb first. The USART’s transmitter and receiver are
functionally independent but use the same data format
and baud rate. The baud rate generator produces a
clock either x16 or x64 of the bit shift rate, depending
on bit BRGH (TXSTA<2>). Parity is not supported by
the hardware, but can be implemented in software (and
stored as the ninth data bit). Asynchronous mode is
stopped during SLEEP.
Asynchronous mode is selected by clearing bit SYNC
(TXSTA<4>).
The USART Asynchronous module consists of the fol-
lowing important elements:
• Baud Rate Generator
• Sampling Circuit
• Asynchronous Transmitter
• Asynchronous Receiver
12.2.1
The USART transmitter block diagram is shown in
Figure 12-7. The heart of the transmitter is the transmit
(serial) shift register (TSR). The shift register obtains its
data from the read/write transmit buffer, TXREG. The
TXREG register is loaded with data in software. The
TSR register is not loaded until the STOP bit has been
transmitted from the previous load. As soon as the
STOP bit is transmitted, the TSR is loaded with new
data from the TXREG register (if available). Once the
TXREG register transfers the data to the TSR register
(occurs in one T
FIGURE 12-7: USART TRANSMIT BLOCK DIAGRAM
DS30390E-page 106
USART Asynchronous Mode
USART ASYNCHRONOUS TRANSMITTER
Applicable Devices
72 73 73A 74 74A 76 77
TXIE
CY
Interrupt
), the TXREG register is empty and
TXEN
TXIF
Baud Rate Generator
SPBRG
Baud Rate CLK
MSb
(8)
TX9D
TSR register
TX9
TXREG register
8
Data Bus
flag bit TXIF (PIR1<4>) is set. This interrupt can be
enabled/disabled by setting/clearing enable bit TXIE
( PIE1<4>). Flag bit TXIF will be set regardless of the
state of enable bit TXIE and cannot be cleared in soft-
ware. It will reset only when new data is loaded into the
TXREG register. While flag bit TXIF indicated the sta-
tus of the TXREG register, another bit TRMT
(TXSTA<1>) shows the status of the TSR register. Sta-
tus bit TRMT is a read only bit which is set when the
TSR register is empty. No interrupt logic is tied to this
bit, so the user has to poll this bit in order to determine
if the TSR register is empty.
Transmission is enabled by setting enable bit TXEN
(TXSTA<5>). The actual transmission will not occur
until the TXREG register has been loaded with data
and the baud rate generator (BRG) has produced a
shift clock (Figure 12-7). The transmission can also be
started by first loading the TXREG register and then
setting enable bit TXEN. Normally when transmission
is first started, the TSR register is empty, so a transfer
to the TXREG register will result in an immediate trans-
fer to TSR resulting in an empty TXREG. A back-to-
back transfer is thus possible (Figure 12-9). Clearing
enable bit TXEN during a transmission will cause the
transmission to be aborted and will reset the transmit-
ter. As a result the RC6/TX/CK pin will revert to hi-
impedance.
In order to select 9-bit transmission, transmit bit TX9
(TXSTA<6>) should be set and the ninth bit should be
written to TX9D (TXSTA<0>). The ninth bit must be
written before writing the 8-bit data to the TXREG reg-
ister. This is because a data write to the TXREG regis-
ter can result in an immediate transfer of the data to the
TSR register (if the TSR is empty). In such a case, an
incorrect ninth data bit maybe loaded in the TSR regis-
ter.
Note 1: The TSR register is not mapped in data
Note 2: Flag bit TXIF is set when enable bit TXEN
LSb
0
memory so it is not available to the user.
is set.
TRMT
Pin Buffer
and Control
SPEN
1997 Microchip Technology Inc.
RC6/TX/CK pin
Related parts for PIC16C72-04E/SP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC16C72-20/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-04/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-20/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-10I/SS](/photos/6/81/68119/150-28-ssop_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SSOP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-04I/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-20I/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-04/SO](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SOP,28PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-10/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-20/SS](/photos/6/81/68119/150-28-ssop_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SSOP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-10/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-20I/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-04/SS](/photos/6/81/68119/150-28-ssop_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SSOP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-10/SS](/photos/6/81/68119/150-28-ssop_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SSOP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-10I/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16C72-04I/SS](/photos/6/81/68119/150-28-ssop_tmb.jpg)
Part Number:
Description:
IC MCU OTP 2KX14 A/D PWM 28SSOP
Manufacturer:
Microchip Technology
Datasheet: