AT89LV51-12AC Atmel, AT89LV51-12AC Datasheet - Page 6

• Manufacturer Part Number: AT89LV51-12AC
• Description: IC MICRO CTRL 12MHZ 44TQFP
• Manufacturer: Atmel
• Series: 89LVr

Specifications of AT89LV51-12AC

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: UART/USART
• Number Of I /o: 32
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Peripherals: -
• Other names: AT89LV5112AC

Program Memory Lock Bits
On the chip are three lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the addi-
tional features listed in the table below:
Lock Bit Protection Modes
Note:
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is pow-
ered up without a reset, the latch initializes to a random
value, and holds that value until reset is activated. It is nec-
essary that the latched value of EA be in agreement with
the current logic level at that pin in order for the device to
function properly.
Programming the Flash
The AT89LV51 is normally shipped with the on-chip Flash
memory array in the erased state (i.e. contents=FFH) and
ready to be programmed.
The respective top-side marking and device signature
codes are listed below:
4-50
Top-Side Mark
Signature
1
2
3
4
Program Lock Bits
1. The lock bits can only be erased with the Chip Erase
LB1
U
P
P
P
operation.
LB2
U
U
P
P
LB3
U
U
U
P
AT89LV51
xxxx
yyww
(030H) = 1EH
(031H) = 61H
(032H) = FFH
Protection Type
No program lock features.
MOVC instructions executed
from external program
memory are disabled from
fetching code bytes from
internal memory, EA is
sampled and latched on
reset, and further
programming of the Flash is
disabled.
Same as mode 2, also verify
is disabled.
Same as mode 3, also
external execution is
disabled.
V
PP
Not
= 12V
(1)
The AT89LV51 code memory array is programmed byte-
by-byte. To program any non-blank byte in the on-chip
Flash Code Memory, the entire memory must be erased
using the Chip Erase Mode.
Programming Algorithm: Before programming the
AT89LV51, the address, data and control signals should be
set up according to the Flash programming mode table and
Figure 3 and Figure 4. To program the AT89LV51, the fol-
lowing sequence should be followed:
1. Input the desired memory location on the address
2. Input the appropriate data byte on the data lines.
3. Activate the correct combination of control signals.
4. Raise EA/V
5. Pulse ALE/PROG once to program a byte in the Flash
Data Polling: The AT89LV51 features Data Polling to indi-
cate the end of a write cycle. During a write cycle, an
attempted read of the last byte written will result in the com-
plement of the written data on PO.7. Once the write cycle
has been completed, true data is valid on all outputs, and
the next cycle may begin. Data Polling may begin any time
after a write cycle has been initiated.
Ready/Busy: The progress of byte programming can also
be monitored by the RDY/BSY output signal. P3.4 is pulled
low after ALE goes high during programming to indicate
BUSY. P3.4 is pulled high again when programming is
done to indicate READY.
Program Verify: If lock bits LB1 and LB2 have not been
programmed, the programmed code data can be read back
via the address and data lines for verification. The lock bits
cannot be verified directly. Verification of the lock bits is
achieved by observing that their features are enabled.
Chip Erase: The entire Flash array and the lock bits are
erased electrically by using the proper combination of con-
trol signals and by holding ALE/PROG low for 10 ms. The
code array is written with all “1”s. The chip erase operation
must be executed before the code memory can be re-pro-
grammed.
Reading the Signature Bytes: The signature bytes are
read by the same procedure as a normal verification of
locations 030H and 031H, except that P3.6 and P3.7 need
to be pulled to a logic low. The values returned are:
lines.
array or the lock bits. The byte-write cycle is self-timed
and typically takes no more than 1.5 ms. Repeat steps
1 through 5 changing the address and data for the
entire array or until the end of the object file is reached.
(030H) = 1EH indicates manufactured by Atmel
(031H) = 61H indicates 89LV51
(032H) = FFH indicates 12V programming
PP
to 12V.