PIC18C252-E/SP Microchip Technology, PIC18C252-E/SP Datasheet - Page 8
![IC MCU OTP 16KX16 A/D 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC18C252-E/SP
Manufacturer Part Number
PIC18C252-E/SP
Description
IC MCU OTP 16KX16 A/D 28DIP
Manufacturer
Microchip Technology
Series
PIC® 18Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16C770-ISO.pdf
(8 pages)
3.PIC18C242-ISO.pdf
(305 pages)
4.PIC18C242-ISO.pdf
(12 pages)
Specifications of PIC18C252-E/SP
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
32KB (16K x 16)
Program Memory Type
OTP
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
28-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
PIC18C252E/SP
PIC18CXX2
5. Module: Interrupts
REGISTER 21-3:
FIGURE 1:
DS80058H-page 8
The operation of the GIE/GIEH bit (INTCON<7>) is
clarified as follows: when the bit is cleared, all
interrupts are disabled. This is regardless of the
state of the IPEN bit (RCON<7>), the priority of the
interrupt, or whether or not the interrupt is
unmasked. This varies from the original descrip-
tion, in which clearing the bit when IPEN = ’1’
would only disable high priority interrupts.
The seventh paragraph in Section 7.0 of the
Device Data Sheet (beginning “When an interrupt
is responded to....”) is amended by adding the fol-
lowing sentence to the end:
Low Priority Interrupt Generation
Peripheral Interrupt Enable bit
Peripheral Interrupt Priority bit
Peripheral Interrupt Flag bit
bit 7
TMR1IE
TMR1IP
TMR1IF
XXXXIF
XXXXIE
XXXXIP
INTERRUPT LOGIC (EXCERPT)
INTCON REGISTER (EXCERPT)
GIE/GIEH: Global Interrupt Enable bit
When IPEN (RCON<7>) = 0:
1 = Enables all unmasked interrupts
0 = Disables all interrupts
When IPEN (RCON<7>) = 1:
1 = Enables all high priority interrupts
0 = Disables all interrupts
Additional Peripheral Interrupts
TMR0IE
TMR0IP
TMR0IF
INT1IF
INT1IE
INT1IP
INT2IF
INT2IE
INT2IP
RBIF
RBIE
RBIP
“It is important to note, however, that clearing the
GIE/GIEH bit, regardless of the state of the IPEN
bit, will disable all interrupts.”
The changes to the bit descriptions in Register 7-1
in the Device Data Sheet are shown in the excerpt
below (changes in bold).
Also, the interrupt logic funnel shown in Figure 7-1
of the Device Data Sheet is amended with the
addition of a GIE/GIEH control line, as shown in
Figure 1 (new material in bold line).
2002 Microchip Technology Inc.
GIEL/PEIE
GIE/GEIH
Interrupt to CPU
Vector to Location
0018h