ATTINY26L-8MI Atmel, ATTINY26L-8MI Datasheet - Page 103

• Manufacturer Part Number: ATTINY26L-8MI
• Description: IC AVR MCU 2K LV 8MHZ IND 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY26L-8MI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ADC Control and
Status Register –
ADCSR
1477K–AVR–08/10
• Bit 7 – ADEN: ADC Enable
Writing a logical “1” to this bit enables the ADC. By clearing this bit to zero, the ADC is turned off.
Turning the ADC off while a conversion is in progress, will terminate this conversion.
• Bit 6 – ADSC: ADC Start Conversion
In Single Conversion mode, a logical “1” must be written to this bit to start each conversion. In
Free Running mode, a logical “1” must be written to this bit to start the first conversion. The first
time ADSC has been written after the ADC has been enabled, or if ADSC is written at the same
time as the ADC is enabled, a dummy conversion will precede the initiated conversion. This
dummy conversion performs initialization of the ADC.
ADSC will read as one as long as a conversion is in progress. When the conversion is complete,
it returns to zero. When a dummy conversion precedes a real conversion, ADSC will stay high
until the real conversion completes. Writing a 0 to this bit has no effect.
• Bit 5 – ADFR: ADC Free Running Select
When this bit is set (one) the ADC operates in Free Running mode. In this mode, the ADC sam-
ples and updates the Data Registers continuously. Clearing this bit (zero) will terminate Free
Running mode.
• Bit 4 – ADIF: ADC Interrupt Flag
This bit is set (one) when an ADC conversion completes and the data registers are updated. The
ADC Conversion Complete Interrupt is executed if the ADIE bit and the I-bit in SREG are set
(one). ADIF is cleared by hardware when executing the corresponding interrupt handling vector.
Alternatively, ADIF is cleared by writing a logical one to the flag. Beware that if doing a read-
modify-write on ADCSR, a pending interrupt can be disabled. This also applies if the SBI and
CBI instructions are used.
• Bit 3 – ADIE: ADC Interrupt Enable
When this bit is set (one) and the I-bit in SREG is set (one), the ADC Conversion Complete Inter-
rupt is activated.
Bit
$06 ($26)
Read/Write
Initial Value
ADEN
R/W
7
0
ADSC
R/W
6
0
ADFR
R/W
5
0
ADIF
R/W
4
0
ADIE
R/W
3
0
ADPS2
R/W
2
0
ADPS1
R/W
1
0
ADPS0
R/W
0
0
ADCSR
103