ATMEGA162-16PJ Atmel, ATMEGA162-16PJ Datasheet - Page 43

• Manufacturer Part Number: ATMEGA162-16PJ
• Description: IC MCU AVR 16K 5V 16MHZ 40-DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA162-16PJ

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -

Power
Management
and Sleep
Modes
MCU Control Register
– MCUCR
MCU Control and
Status Register –
MCUCSR
2513K–AVR–07/09
Sleep modes enable the application to shut down unused modules in the MCU, thereby saving
power. The AVR provides various sleep modes allowing the user to tailor the power consump-
tion to the application’s requirements.
To enter any of the five sleep modes, the SE bit in MCUCR must be written to logic one and a
SLEEP instruction must be executed. The SM2 bit in MCUCSR, the SM1 bit in MCUCR, and the
SM0 bit in the EMCUCR Register select which sleep mode (Idle, Power-down, Power-save,
Standby, or Extended Standby) will be activated by the SLEEP instruction. See
summary. If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU wakes up.
The MCU is then halted for four cycles in addition to the start-up time, executes the interrupt rou-
tine, and resumes execution from the instruction following SLEEP. The contents of the Register
File and SRAM are unaltered when the device wakes up from sleep. If a Reset occurs during
sleep mode, the MCU wakes up and executes from the Reset Vector.
Figure 18 on page 35
tion. The figure is helpful in selecting an appropriate sleep mode.
• Bit 5 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
• Bit 4 – SM1: Sleep Mode Select Bit 1
The Sleep Mode Select bits select between the five available sleep modes as shown in
16.
• Bit 5 – SM2: Sleep Mode Select Bit 2
The Sleep Mode Select bits select between the five available sleep modes as shown in
16.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
SRE
R/W
JTD
R/W
7
0
7
0
SRW10
presents the different clock systems in the ATmega162, and their distribu-
R/W
R/W
6
0
6
–
0
SM2
R/W
R/W
SE
5
0
5
0
JTRF
SM1
R/W
R/W
4
0
4
0
WDRF
ISC11
R/W
R/W
3
0
3
0
BORF
ISC10
R/W
R/W
2
0
2
0
EXTRF
ISC01
R/W
R/W
1
0
1
0
ATmega162/V
ISC00
PORF
R/W
R/W
0
0
0
0
MCUCSR
MCUCR
Table 16
Table
Table
for a
43