ATTINY44-20PU Atmel, ATTINY44-20PU Datasheet - Page 161

• Manufacturer Part Number: ATTINY44-20PU
• Description: IC MCU AVR 4K FLASH 20MHZ 14-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY44-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-DIP (0.300", 7.62mm)
• Package: 14PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Interface Type: SPI/USI
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 2
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.2.1
19.3
8006K–AVR–10/10
Device Signature Imprint Table
Latching of Fuses
Table 19-5.
Notes:
Note that fuse bits are locked if Lock Bit 1 (LB1) is programmed. Fuse bits should be pro-
grammed before lock bits. The status of fuse bits is not affected by chip erase.
Fuse bits can also be read by device firmware. See section
Data from Software” on page
Fuse values are latched when the device enters programming mode and changes to fuse values
have no effect until the part leaves programming mode. This does not apply to the EESAVE
Fuse which will take effect once it is programmed. Fuses are also latched on power-up.
The device signature imprint table is a dedicated memory area used for storing miscellaneous
device information, such as the device signature and oscillator calibration data. Most of this
memory segment is reserved for internal use, as outlined in
Table 19-6.
Notes:
Fuse Low Byte
CKDIV8
CKOUT
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
Address
0x00
0x01
0x02
0x03
0x04
0x05 ... 0x2A
(3)
(3)
1. See
2. Allows system clock to be output on pin. See
3. The default value results in maximum start-up time for the default clock source. See
4. The default setting results in internal RC Oscillator @ 8.0 MHz. See
1. See section “Signature Bytes” for more information.
2. See section “Calibration Byte” for more information.
(2)
(1)
(4)
(4)
(4)
(4)
on page 27
details.
Fuse Low Byte
Contents of Device Signature Imprint Table.
“System Clock Prescaler” on page 30
High Byte
Signature byte 0
Calibration data for internal oscillator
Signature byte 1
Reserved for internal use
Signature byte 2
Reserved for internal use
for details.
Bit No
155.
7
6
5
4
3
2
1
0
(1)
(1)
(1)
Description
Divide clock by 8
Clock Output Enable
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
for details.
(2)
“Clock Output Buffer” on page 30
“Reading Lock, Fuse and Signature
Table
19-6.
Default Value
0 (programmed)
1 (unprogrammed)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
0 (programmed)
ATtiny24/44/84
Table 6-4 on page 27
for details.
Table 6-5
161
for