EP9301-CQ Cirrus Logic Inc, EP9301-CQ Datasheet - Page 9
![IC ARM920T MCU 166MHZ 208-LQFP](/photos/12/23/122383/mfg_ep9301_parts_sml.jpg)
EP9301-CQ
Manufacturer Part Number
EP9301-CQ
Description
IC ARM920T MCU 166MHZ 208-LQFP
Manufacturer
Cirrus Logic Inc
Series
EP9r
Datasheets
1.EDB9301.pdf
(5 pages)
2.EDB9301.pdf
(4 pages)
3.EP9307-CRZ.pdf
(824 pages)
4.EP9301-IQ.pdf
(41 pages)
Specifications of EP9301-CQ
Core Processor
ARM9
Core Size
16/32-Bit
Speed
166MHz
Connectivity
EBI/EMI, Ethernet, I²C, IrDA, SPI, UART/USART, USB
Peripherals
AC'97, DMA, I²:S, LED, MaverickKey, POR, PWM, WDT
Number Of I /o
19
Program Memory Type
ROMless
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
1.65 V ~ 3.6 V
Data Converters
A/D 5x12b
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
208-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Program Memory Size
-
Other names
598-1248
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP9301-CQZ
Manufacturer:
CIRRUS
Quantity:
3 390
Part Number:
EP9301-CQZ
Manufacturer:
CIRRUSLOGIC
Quantity:
20 000
Company:
Part Number:
EP9301-CQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
PLL and Clocking
The Processor and the Peripheral Clocks operate from a
single 14.7456 MHz crystal.
The Real Time Clock operates from a 32.768 KHz
external oscillator.
Timers
The Watchdog Timer ensures proper operation by
requiring periodic attention to prevent a reset-on-time-
out.
Two 16-bit timers operate as free-running down counters
or as periodic timers for fixed-interval interrupts and have
a range of 0.03 ms to 4.27 seconds.
One 32-bit timer, plus a 6-bit prescale counter, has a
range of 0.03 µs to 73.3 hours.
One 40-bit debug timer, plus a 6-bit prescale counter, has
a range of 1.0 µs to 12.7 days.
Interrupt Controller
The interrupt controller allows up to 54 interrupts to
generate an Interrupt Request (IRQ) or Fast Interrupt
Request (FIQ) signal to the processor core. Thirty-two
hardware priority assignments are provided for assisting
IRQ vectoring, and two levels are provided for FIQ
vectoring. This allows time-critical interrupts to be
processed in the shortest time possible. Internal
interrupts may be programmed as active high or active
low level sensitive inputs. GPIO pins programmed as
interrupts may be programmed as active high level
sensitive, active low level sensitive, rising edge triggered,
falling edge triggered, or combined rising/falling edge
triggered.
•
•
•
•
DS636PP5
XTALI
XTALO
VDD_PLL
GND_PLL
Supports 54 interrupts from a variety of sources (such
as UARTs, GPIO and ADC)
Routes interrupt sources to either the ARM920T’s
IRQ or FIQ (Fast IRQ) inputs
Three dedicated off-chip interrupt lines INT[2:0]
operate as active-high level-sensitive interrupts
Any of the 19 GPIO lines maybe configured to
generate interrupts
Pin Mnemonic
Table J. PLL and Clocking Pin Assignments
Main Oscillator Input
Main Oscillator Output
Main Oscillator Power
Main Oscillator Ground
Pin Name - Description
©
Copyright 2005 Cirrus Logic (All Rights Reserved)
•
Dual LED Drivers
Two pins are assigned specifically to drive external
LEDs.
General Purpose Input/Output (GPIO)
The 16 EGPIO and the 3 FGPIO pins may each be
configured individually as an output, an input or an
interrupt input.
There are 10 pins that may alternatively be used as input,
output, or open-drain pins, but do not support interrupts.
These pins are:
6 pins may alternatively be used as inputs only:
2 pins may alternatively be used as outputs only:
EGPIO[15:0]
FGPIO[3:1]
INT[3] and INT[1:0]
GRLED
REDLED
Pin Mnemonic
Software supported priority mask for all FIQs and
IRQs
Note:
Pin Mnemonic
Pin Mnemonic
Table M. General Purpose Input/Output Pin Assignment
Table K. External Interrupt Controller Pin Assignment
• Ethernet MDIO
• Both LED Outputs
• EEPROM Clock and Data
• HGPIO[5:2]
• CGPIO[0]
• CTSn, DSRn / DCDn
• 3 Interrupt Lines
• RTSn
• ARSTn
INT[2] is not bonded out.
Entry Level ARM9 System-on-Chip Processor
Table L. Dual LED Pin Assignments
Green LED
Red LED
Description
Pin Name -
Expanded General Purpose Input / Output
Pins with Interrupts
Expanded General Purpose Input / Output
Pins with Interrupts
External Interrupts 2, 1, 0
Pin Name - Description
Pin Name - Description
General Purpose I/O
General Purpose I/O
Alternative Usage
EP9301
9