SX28AC/SS-G Parallax Inc, SX28AC/SS-G Datasheet - Page 26

• Manufacturer Part Number: SX28AC/SS-G
• Description: IC RISC MCU 2KX12 EE/FLASH28S
• Manufacturer: Parallax Inc
• Series: SXr

Specifications of SX28AC/SS-G

• Core Size: 8-Bit
• Program Memory Size: 3KB (2K x 12)
• Oscillator Type: Internal
• Core Processor: RISC
• Speed: 75MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 20
• Program Memory Type: FLASH
• Ram Size: 136 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: SX
• No. Of I/o's: 20
• Eeprom Memory Size: 2048Byte
• Ram Memory Size: 136Byte
• Cpu Speed: 75MHz
• Processor Series: Ubicom SXx
• Core: RISC
• Data Bus Width: 8 bit
• Data Ram Size: 136 B
• Maximum Clock Frequency: 75 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 1
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: 32300, 45302
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Parallax SX20AC/SX28AC
10.0 REAL TIME CLOCK (RTCC)/WATCHDOG TIMER
The device contains an 8-bit Real Time Clock/Counter
(RTCC) and an 8-bit Watchdog Timer (WDT). An 8-bit
programmable prescaler extends the RTCC to 16 bits. If
the prescaler is not used for the RTCC, it can serve as a
postscaler for the Watchdog Timer. Figure 10-1 shows the
RTCC and WDT block diagram.
10.1. RTCC
RTCC is an 8-bit real-time timer that is incremented once
each instruction cycle or from a transition on the RTCC
pin. The on-board prescaler can be used to extend the
RTCC counter to 16 bits.
The RTCC counter can be clocked by the internal
instruction cycle clock or by an external clock source
presented at the RTCC pin.
To select the internal clock source, bit 5 of the OPTION
register should be cleared. In this mode, RTCC is
incremented at each instruction cycle unless the prescaler
is selected to increment the counter.
To select the external clock source, bit 5 of the OPTION
register must be set. In this mode, the RTCC counter is
incremented with each valid signal transition at the RTCC
pin. By using bit 4 of the OPTION register, the transition
can be programmed to be either a falling edge or rising
edge. Setting the control bit selects the falling edge to
increment the counter. Clearing the bit selects the rising
edge.
© Parallax Inc.
Page 26 of 51
The RTCC generates an interrupt as a result of an RTCC
rollover from 0FF to 000. There is no interrupt pending
bit to indicate the overflow occurrence. The RTCC
register must be sampled by the program to determine any
overflow occurrence.
10.2.
The watchdog logic consists of a Watchdog Timer which
shares the same 8-bit programmable prescaler with the
RTCC. The prescaler actually serves as a postscaler if
used in conjunction with the WDT, in contrast to its use
as a prescaler with the RTCC.
10.3.
The 8-bit prescaler may be assigned to either the RTCC or
the WDT through the PSA bit (bit 3 of the OPTION
register). Setting the PSA bit assigns the prescaler to the
WDT. If assigned to the WDT, the WDT clocks the
prescaler and the prescaler divide rate is selected by the
PS0, PS1, and PS2 bits located in the OPTION register.
Clearing the PSA bit assigns the prescaler to the RTCC.
Once assigned to the RTCC, the prescaler clocks the
RTCC and the divide rate is selected by the PS0, PS1, and
PS2 bits in the OPTION register. The prescaler is not
mapped into the data memory, so run-time access is not
possible. The prescaler cannot be assigned to both the
RTCC and WDT simultaneously.
Watchdog Timer
The Prescaler
Figure 10-1
RTCC and WDT Block Diagram
Rev 1.6 11/20/2006
www.parallax.com