C8051F006 Silicon Laboratories Inc, C8051F006 Datasheet - Page 168
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F006
Manufacturer Part Number
C8051F006
Description
IC 8051 MCU 32K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F00xr
Specifications of C8051F006
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
2.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x12b, D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP, 48-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F006
Manufacturer:
TOSHIBA
Quantity:
100
Company:
Part Number:
C8051F006
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F006-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F006-GQR
Manufacturer:
SILICON
Quantity:
1 200
Company:
Part Number:
C8051F006-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F006R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Bit15
WRMD3
This register determines how the Flash interface logic will respond to reads and writes to the
FLASHDAT Register.
Bits7-4: WRMD3-0: Write Mode Select Bits.
Bits3-0: RDMD3-0: Read Mode Select Bits.
This register holds the address for all JTAG Flash read, write, and erase operations. This register
autoincrements after each read or write, regardless of whether the operation succeeded or failed.
Bits15-0: Flash Operation 16-bit Address.
Bit7
The Write Mode Select Bits control how the interface logic responds to writes to the
FLASHDAT Register per the following values:
0000: A FLASHDAT write replaces the data in the FLASHDAT register, but is otherwise
0001: A FLASHDAT write initiates a write of FLASHDAT into the memory location
0010: A FLASHDAT write initiates an erasure (sets all bytes to 0xFF) of the Flash page
(All other values for WRMD3-0 are reserved.)
The Read Mode Select Bits control how the interface logic responds to reads to the
FLASHDAT Register per the following values:
0000: A FLASHDAT read provides the data in the FASHDAT register, but is otherwise
0001: A FLASHDAT read initiates a read of the byte addressed by the FLASHADR register
0010: A FLASHDAT read initiates a read of the byte addressed by FLASHADR only if no
(All other values for RDMD3-0 are reserved.)
WRMD2
Bit6
ignored.
addressed by the FLASHADR register. FLASHADR is incremented by one when
complete.
containing the address in FLASHADR. FLASHDAT must be 0xA5 for the erase to
occur. FLASHADR is not affected. If FLASHADR = 0x7DFE – 0x7DFF, the entire
user space will be erased (i.e. entire Flash memory except for Reserved area 0x7E00 –
0x7FFF).
ignored.
if no operation is currently active. This mode is used for block reads.
operation is active and any data from a previous read has already been read from
FLASHDAT. This mode allows single bytes to be read (or the last byte of a block)
without initiating an extra read.
Figure 21.4. FLASHADR: JTAG Flash Address Register
Figure 21.3. FLASHCON: JTAG Flash Control Register
WRMD1
Bit5
WRMD0
Bit4
Rev. 1.7
RDMD3
Bit3
RDMD2
Bit2
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
RDMD1
Bit1
RDMD0
Bit0
Bit0
Reset Value
Reset Value
00000000
0x0000
168