MCP6004-I/SL Microchip Technology, MCP6004-I/SL Datasheet - Page 15
![IC OPAMP QUAD 1.8V 14SOIC](/photos/6/59/65933/150-14-soic_sml.jpg)
MCP6004-I/SL
Manufacturer Part Number
MCP6004-I/SL
Description
IC OPAMP QUAD 1.8V 14SOIC
Manufacturer
Microchip Technology
Specifications of MCP6004-I/SL
Slew Rate
0.6 V/µs
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Amplifier Type
General Purpose
Number Of Circuits
4
Output Type
Rail-to-Rail
Gain Bandwidth Product
1MHz
Current - Input Bias
1pA
Voltage - Input Offset
4500µV
Current - Supply
100µA
Current - Output / Channel
23mA
Voltage - Supply, Single/dual (±)
1.8 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Number Of Channels
4
Common Mode Rejection Ratio (min)
60 dB
Input Offset Voltage
4.5 mV
Input Bias Current (max)
19 pA
Operating Supply Voltage
3 V, 5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Shutdown
No
Supply Voltage (max)
6 V
Supply Voltage (min)
1.8 V
Technology
CMOS
Voltage Gain Db
112 dB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP6004-I/SL
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP6004-I/SL,MCP6004T-I/SL
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
FIGURE 4-6:
for Inverting Gain.
1.
2.
4.7
4.7.1
The rail-to-rail input and output capability of the
MCP6001/2/4 op amp is ideal for unity-gain buffer
applications. The low quiescent current and wide
bandwidth makes the device suitable for a buffer
configuration in an instrumentation amplifier circuit, as
shown in
© 2009 Microchip Technology Inc.
Non-inverting Gain and Unity-Gain Buffer:
a.
b.
Inverting Gain and Transimpedance Gain
Amplifiers (convert current to voltage, such as
photo detectors):
a.
b.
Connect the non-inverting pin (V
input with a wire that does not touch the
PCB surface.
Connect the guard ring to the inverting input
pin (V
common mode input voltage.
Connect the guard ring to the non-inverting
input pin (V
to the same reference voltage as the op
amp (e.g., V
Connect the inverting pin (V
with a wire that does not touch the PCB
surface.
Application Circuits
Figure
UNITY-GAIN BUFFER
IN
4-7.
–). This biases the guard ring to the
V
IN
IN
Guard Ring
DD
+). This biases the guard ring
Example Guard Ring Layout
-
/2 or ground).
V
IN
+
IN
–) to the input
IN
V
SS
+) to the
FIGURE 4-7:
with Unity-Gain Buffer Inputs.
4.7.2
The MCP6001/2/4 op amp’s low input bias current
makes it possible for the designer to use larger
resistors and smaller capacitors for active low-pass
filter
increases, the noise generated also increases.
Parasitic capacitances and the large value resistors
could also modify the frequency response. These
trade-offs need to be considered when selecting circuit
elements.
Usually, the op amp bandwidth is 100x the filter cutoff
frequency (or higher) for good performance. It is
possible to have the op amp bandwidth 10X higher
than the cutoff frequency, thus having a design that is
more sensitive to component tolerances.
Figure 4-8
100 kHz cutoff frequency and a gain of +1 V/V; the op
amp bandwidth is only 10x higher than the cutoff
frequency. The component values were selected using
Microchip’s FilterLab
FIGURE 4-8:
Low-Pass Filter.
MCP6001/1R/1U/2/4
V
V
V
IN2
IN
IN1
applications.
14.3 kΩ
V
shows a second-order Butterworth filter with
OUT
ACTIVE LOW-PASS FILTER
MCP6002
MCP6002
+
–
+
–
1/2
1/2
53.6 kΩ
33 pF
=
(
V
®
IN2
However,
software.
Instrumentation Amplifier
Active Second-Order
–
100 pF
R
V
R
2
IN1
2
)
•
R
MCP6002
V
+
–
–
+
MCP6001
as
REF
R
----- -
R
1
1
2
R
DS21733J-page 15
+
1
the
V
REF
R
R
1
2
= 20 kΩ
= 10 kΩ
resistance
V
V
OUT
OUT