MCP6293-E/SN Microchip Technology, MCP6293-E/SN Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP6293-E/SN
Manufacturer Part Number
MCP6293-E/SN
Description
IC OPAMP 2.4V SNGL CS R-R 8SOIC
Manufacturer
Microchip Technology
Datasheets
1.PIC16F690DM-PCTLHS.pdf
(36 pages)
2.MCP6291T-EOT.pdf
(16 pages)
3.MCP6293T-ECH.pdf
(32 pages)
Specifications of MCP6293-E/SN
Slew Rate
7 V/µs
Amplifier Type
General Purpose
Number Of Circuits
1
Output Type
Rail-to-Rail
Gain Bandwidth Product
10MHz
Current - Input Bias
1pA
Voltage - Input Offset
3000µV
Current - Supply
1mA
Current - Output / Channel
25mA
Voltage - Supply, Single/dual (±)
2.4 V ~ 6 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Op Amp Type
General Purpose
No. Of Amplifiers
1
Bandwidth
10MHz
Supply Voltage Range
2.4V To 5.5V
Amplifier Case Style
SOIC
No. Of Pins
8
Operating Temperature Range
-40°C To
Number Of Channels
1
Voltage Gain Db
110 dB
Common Mode Rejection Ratio (min)
70 dB
Input Offset Voltage
3 mV
Operating Supply Voltage
3 V, 5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Request inventory verification / Request inventory verification
-3db Bandwidth
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP6293-E/SN
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP6293-E/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
MCP6291/2/3/4/5
FIGURE 4-4:
for Capacitive Loads.
After selecting R
resulting frequency response peaking and step
response overshoot. Modify R
response is reasonable. Bench evaluation and
simulations with the MCP6291/2/3/4/5 SPICE macro
model are helpful.
4.4
The MCP6293 and MCP6295 are single and dual op
amps with Chip Select (CS), respectively. When CS is
pulled high, the supply current drops to 0.7 µA (typ.)
and flows through the CS pin to V
happens, the amplifier output is put into a high-imped-
ance state. By pulling CS low, the amplifier is enabled.
If the CS pin is left floating, the amplifier may not
operate properly. Figure 1-1 shows the output voltage
and supply current response to a CS pulse.
4.5
The MCP6295 is a dual op amp with Chip Select (CS).
The Chip Select input is available on what would be the
non-inverting input of a standard dual op amp (pin 5).
This is available because the output of op amp A
connects to the non-inverting input of op amp B, as
shown in Figure 4-5. The Chip Select input, which can
be connected to a microcontroller I/O line, puts the
device in Low-power mode. Refer to Section 4.3
“MCP6293/5 Chip Select (CS)”.
DS21812D-page 12
100
10
MCP629X Chip Select (CS)
Cascaded Dual Op Amps
(MCP6295)
10
Normalized Load Capacitance; C
ISO
for your circuit, double-check the
100
Recommended R
G
G
N
N
= 1 V/V
ISO
2 V/V
1,000
's value until the
SS
L
/G
. When this
N
ISO
(pF)
Values
10,000
FIGURE 4-5:
The output of op amp A is loaded by the input imped-
ance of op amp B, which is typically 10
specified in the DC specification table (Refer to
Section 4.3 “Capacitive Loads” for further details
regarding capacitive loads).
The common mode input range of these op amps is
specified in the data sheet as V
V
is limited to V
10 k load), the non-inverting input range of op amp B
is limited to the common mode input range of
V
4.6
With this family of operational amplifiers, the power
supply pin (V
bypass capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm
for good high-frequency performance. It also needs a
bulk capacitor (i.e., 1 µF or larger) within 100 mm to
provide large, slow currents. This bulk capacitor can be
shared with other analog parts.
4.7
In applications where low input bias current is critical,
Printed Circuit Board (PCB) surface-leakage effects
need to be considered. Surface leakage is caused by
humidity, dust or other contamination on the board.
Under low humidity conditions, a typical resistance
between nearby traces is 10
cause 5 pA of current to flow, which is greater than the
MCP6291/2/3/4/5 family’s bias current at 25°C (1 pA,
typ.).
The easiest way to reduce surface leakage is to use a
guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin.
An example of this type of layout is shown in
Figure 4-6.
V
V
DD
SS
INA
INA
+ 20 mV and V
+ 300 mV. However, since the output of op amp A
+
–
2
3
Supply Bypass
PCB Surface Leakage
DD
OL
A
V
for single supply) should have a local
and V
OUTA
DD
1
MCP6295
/V
Cascaded Gain Amplifier.
OH
– 20 mV.
2004 Microchip Technology Inc.
INB
CS
(20 mV from the rails with a
+ V
12
5
. A 5V difference would
INB
6
–
SS
B
– 300 mV and
13
7
6 pF, as
V
OUTB