MCP607-I/P Microchip Technology, MCP607-I/P Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP607-I/P
Manufacturer Part Number
MCP607-I/P
Description
IC OPAMP 2.5V DUAL R-R 8DIP
Manufacturer
Microchip Technology
Specifications of MCP607-I/P
Slew Rate
0.08 V/µs
Package / Case
8-DIP (0.300", 7.62mm)
Amplifier Type
General Purpose
Number Of Circuits
2
Output Type
Rail-to-Rail
Gain Bandwidth Product
155kHz
Current - Input Bias
1pA
Voltage - Input Offset
250µV
Current - Supply
18.7µA
Current - Output / Channel
17mA
Voltage - Supply, Single/dual (±)
2.5 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Number Of Channels
2
Common Mode Rejection Ratio (min)
75 dB
Input Offset Voltage
0.25 mV
Input Bias Current (max)
1 pA
Operating Supply Voltage
3 V, 5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
Through Hole
Shutdown
No
Supply Voltage (max)
6 V
Supply Voltage (min)
2.5 V
Technology
CMOS
Voltage Gain Db
121 dB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP607-I/P
Manufacturer:
Microchip
Quantity:
4 108
Part Number:
MCP607-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
4.0
The MCP606/7/8/9 family of op amps is manufactured
using Microchip’s state-of-the-art CMOS process
These op amps are unity-gain stable and suitable for a
wide range of general purpose applications.
4.1
4.1.1
The MCP606/7/8/9 op amp is designed to prevent
phase reversal when the input pins exceed the supply
voltages.
exceeding the supply voltage without any phase
reversal.
4.1.2
The ESD protection on the inputs can be depicted as
shown in
protect the input transistors, and to minimize input bias
current (I
when they try to go more than one diode drop below
V
above V
allow normal operation, and low enough to bypass
quick ESD events within the specified limits.
FIGURE 4-1:
Structures.
In order to prevent damage and/or improper operation
of these op amps, the circuit they are in must limit the
currents and voltages at the V
Absolute Maximum Ratings † at the beginning of
Section 1.0 “Electrical Characteristics”).
shows the recommended approach to protecting these
inputs. The internal ESD diodes prevent the input pins
(V
the resistors R
out of the input pins. Diodes D
input pins (V
V
implemented as shown, resistors R
the current through D
© 2009 Microchip Technology Inc.
SS
DD
IN
. They also clamp any voltages that go too far
+ and V
, and dump any currents onto V
V
V
V
IN
DD
SS
+
DD
APPLICATIONS INFORMATION
Rail-to-Rail Inputs
B
). The input ESD diodes clamp the inputs
Figure
; their breakdown voltage is high enough to
Figure 2-23
Bond
Bond
Bond
PHASE REVERSAL
INPUT VOLTAGE AND CURRENT
LIMITS
Pad
Pad
Pad
IN
IN
–) from going too far below ground, and
1
+ and V
and R
4-1. This structure was chosen to
1
2
Simplified Analog Input ESD
and D
limit the possible current drawn
IN
Stage
Input
shows
–) from going too far above
2
.
IN
1
+ and V
the
and D
1
and R
Bond
Pad
input
2
IN
prevent the
– pins (see
DD
2
Figure 4-2
V
also limit
. When
IN
voltage
–
FIGURE 4-2:
Inputs.
It is also possible to connect the diodes to the left of
resistors R
diodes D
mechanism. The resistors then serve as in-rush current
limiters; the DC current into the input pins (V
V
A significant amount of current can flow out of the
inputs when the common mode voltage (V
ground (V
high impedance may need to limit the useable voltage
range.
4.1.3
The input stage of the MCP606/7/8/9 op amps use a
PMOS input stage. It operates at low common mode
input voltage (V
topology, the device operates with V
and 0.3V below V
Figure 4-3
same voltage as the inverting input, V
below V
FIGURE 4-3:
Limited V
IN
–) should be very small.
V
V
1
2
DD
1
R
R
V
SS
OUT
–1.2V for correct operation.
shows a unity gain buffer. Since V
1
2
1
and D
IN
NORMAL OPERATION
>
>
); see
and R
R
R
V
V
Range.
1
2
D
SS
SS
2
SS
1
CM
MCP606/7/8/9
2
needs to be limited by some other
– (minimum expected V
– (minimum expected V
.
+
–
Figure
MCP60X
. In this case, current through the
), including ground. WIth this
D
Protecting the Analog
Unity Gain Buffer has a
2
2-31. Applications that are
2 mA
2 mA
MCP60X
V
R
CM
DD
3
DS11177F-page 15
OUT
up to V
V
OUT
must be kept
CM
1
2
)
)
OUT
) is below
DD
IN
+ and
–1.1V
is the