LT1351CS8#PBF Linear Technology, LT1351CS8#PBF Datasheet
LT1351CS8#PBF
Specifications of LT1351CS8#PBF
Available stocks
Related parts for LT1351CS8#PBF
LT1351CS8#PBF Summary of contents
Page 1
... LT1351 see the LT1352/LT1353 data sheet. For higher bandwidth devices with higher supply current see the LT1354 through LT1365 data sheets. Singles, duals and quads of each amplifier are available. , LTC and LT are registered trademarks of Linear Technology Corporation. C-Load is a trademark of Linear Technology Corporation. R4 50k – ...
Page 2
LT1351 ABSOLUTE MAXIMUM + – Total Supply Voltage ( .............................. 36V Differential Input Voltage (Transient Only, Note 1) ... 10V Input Voltage .......................................................... V Output Short-Circuit Duration (Note 2) ........... Indefinite Operating Temperature Range ...
Page 3
ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER A Large-Signal Voltage Gain VOL V Output Swing OUT I Output Current OUT I Short-Circuit Current SC SR Slew Rate Full-Power Bandwidth GBW Gain Bandwidth Rise Time, Fall Time r f Overshoot Propagation ...
Page 4
LT1351 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER CMRR Common Mode Rejection Ratio PSRR Power Supply Rejection Ratio A Large-Signal Voltage Gain VOL V Output Swing OUT I Output Current OUT I Short-Circuit Current SC SR Slew Rate GBW Gain Bandwidth I Shutdown ...
Page 5
ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER V Output Swing OUT I Output Current OUT I Short-Circuit Current SC SR Slew Rate GBW Gain Bandwidth I Shutdown Input Current SHDN I Supply Current S Note 1: Differential inputs of 10V are appropriate for ...
Page 6
LT1351 W U TYPICAL PERFORMANCE CHARACTERISTICS Input Bias Current vs Temperature 15V – 125 –50 ...
Page 7
W U TYPICAL PERFORMANCE CHARACTERISTICS Gain and Phase vs Frequency – PHASE 15V V = 15V ...
Page 8
LT1351 W U TYPICAL PERFORMANCE CHARACTERISTICS Slew Rate vs Supply Voltage 200 – – ( )/2 150 100 50 0 ...
Page 9
W U TYPICAL PERFORMANCE CHARACTERISTICS Small-Signal Transient ( 1351 G31 Large-Signal Transient ( 1351 G34 U U APPLICATIONS INFORMATION The LT1351 may be inserted directly into many high speed amplifier applications improving both DC ...
Page 10
LT1351 U U APPLICATIONS INFORMATION noise gain is one and a large feedback resistor is used, C should be greater than or equal I-to-V converter as shown in the Typical Applications section. Capacitive Loading The LT1351 ...
Page 11
U U APPLICATIONS INFORMATION resistive load) the network is incompletely bootstrapped and adds to the compensation at the high impedance node. The added capacitance slows down the amplifier and a zero is created by the RC combination, both of W ...
Page 12
LT1351 U TYPICAL APPLICATIONS INPUTS Shutdown Circuit 3 + LT1351 2 – 1N4148 SHDN SST177 DAC I-to-V Converter 10pF 12 5k DAC – LT1351 565A TYPE + V 5k OUT + ...
Page 13
PACKAGE DESCRIPTION 0.007 (0.18) 0.021 0.006 (0.53 0.015) * DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR ...
Page 14
LT1351 PACKAGE DESCRIPTION 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) +0.035 0.325 –0.015 +0.889 8.255 –0.381 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) ...
Page 15
... FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... DROOP: 20nA/2000pF = 10mV/ms ACQUISITION TIME: 10V, 0. CHARGE INJECTION ERROR: 8pC/2000pF = 4mV COMMENTS Good DC Precision, Stable with All Capacitive Loads Good DC Precision, Stable with All Capacitive Loads V OUT 1351 TA06 1351fa LT/TP 0498 REV A 2K • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1996 ...