OP270GPZ Analog Devices Inc, OP270GPZ Datasheet - Page 14

• Manufacturer Part Number: OP270GPZ
• Description: IC OPAMP GP 5MHZ DUAL PREC 8DIP
• Manufacturer: Analog Devices Inc
• Type: General Purpose Amplifierr

Specifications of OP270GPZ

• Slew Rate: 2.4 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Gain Bandwidth Product: 5MHz
• Current - Input Bias: 15nA
• Voltage - Input Offset: 50µV
• Current - Supply: 4mA
• Voltage - Supply, Single/dual (±): ±4.5 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Op Amp Type: Low Noise
• No. Of Amplifiers: 2
• Bandwidth: 5MHz
• Supply Voltage Range: ± 4.5V To ± 18V
• Amplifier Case Style: DIP
• No. Of Pins: 8
• Channel Separation: 175
• Common Mode Rejection Ratio: 110
• Current, Input Bias: 15 nA
• Current, Input Offset: 5 nA
• Current, Supply: 4 mA
• Impedance, Thermal: 37 °C/W
• Number Of Amplifiers: Dual
• Package Type: PDIP-8
• Resistance, Input: 0.4 Megohms (Differential), 20 Gigaohms (Common-Mode)
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 1500 V/mV
• Voltage, Input: ±12.5 V
• Voltage, Noise: 3.6 nV/sqrt Hz
• Voltage, Offset: 50 μV
• Voltage, Output, High: +13.5 V
• Voltage, Output, Low: -13.5 V
• Voltage, Supply: ±15 V
• Rail/rail I/o Type: No
• Number Of Elements: 2
• Unity Gain Bandwidth Product: 5MHz
• Input Offset Voltage: 250uV
• Input Bias Current: 60nA
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): ±5/±9/±12/±15V
• Voltage Gain In Db: 123.52dB
• Power Supply Rejection Ratio: 116.48dB
• Power Supply Requirement: Dual
• Shut Down Feature: No
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (max): ±18V
• Technology: Bipolar
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Current - Output / Channel: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

OP270
NOISE MEASUREMENTS
Peak-to-Peak Voltage Noise
The circuit of Figure 35 is a test setup for measuring peak-to-
peak voltage noise. To measure the 200 nV peak-to-peak noise
specification of the OP270 in the 0.1 Hz to 10 Hz range, the
following precautions must be observed:
•
•
•
•
•
•
The device has to be warmed up for at least five minutes.
As shown in the warm-up drift curve (see Figure 8), the
offset voltage typically changes 2 μV due to increasing chip
temperature after power-up. In the 10 sec measurement
interval, these temperature-induced effects can exceed tens
of nanovolts.
For similar reasons, the device has to be well shielded from
air currents. Shielding also minimizes thermocouple effects.
Sudden motion in the vicinity of the device can also feed
through to increase the observed noise.
The test time to measure noise of 0.1 Hz to 10 Hz should
not exceed 10 sec. As shown in the noise-tester frequency
response curve of Figure 36, the 0.1 Hz corner is defined by
only one pole. The test time of 10 sec acts as an additional
pole to eliminate noise contribution from the frequency
band below 0.1 Hz.
A noise voltage density test is recommended when measuring
noise on several units. A 10 Hz noise voltage density mea-
surement correlates well with a 0.1 Hz to 10 Hz peak-to-peak
noise reading because both results are determined by the
white noise and the location of the 1/f corner frequency.
Power should be supplied to the test circuit by well bypassed
low noise supplies, such as batteries. Such supplies will min-
imize output noise introduced via the amplifier supply pins.
100
80
60
40
20
0
0.01
Figure 36. 0.1 Hz to 10 Hz Peak-to-Peak Voltage Noise
Test Circuit Frequency Response
0.1
FREQUENCY (Hz)
1
10
100
Rev. E | Page 14 of 20
Noise Measurement—Noise Voltage Density
The circuit of Figure 37 shows a quick and reliable method for
measuring the noise voltage density of dual op amps. The first
amplifier is in unity gain, with the final amplifier in a noninverting
gain of 101. Because the noise voltages of the amplifiers are
uncorrelated, they add in rms to yield
The OP270 is a monolithic device with two identical amplifiers.
Therefore, the noise voltage densities of the amplifiers match,
giving
Noise Measurement—Current Noise Density
The test circuit shown in Figure 38 can be used to measure current
noise density. The formula relating the voltage output to the current
noise density is
where:
G is a gain of 10,000.
R
S
= 100 kΩ source resistance.
R1
5Ω
e
e
i
n
OUT
OUT
=
100kΩ
R2
=
=
OP270
⎛
⎜
⎝
101
101
1/2
e
Figure 37. Noise Voltage Density Test Circuit
nOUT
Figure 38. Current Noise Density Test Circuit
G
OP270
DUT
1.24kΩ
(
(
100Ω
R1
R3
( ) ( )
2
e
⎞
⎟
⎠
200Ω
e
e
V
nA
2
n
OUT
S
R4
2
−
= ±15V
2
)
R
(
(nV/√Hz) ≈ 101 (√2e
=
40
S
+
101
nV
e
OP270
OP27E
nB
1/2
10kΩ
(
R2
/
2
2
8.06kΩ
)
e
Hz
n
TO SPECTRUM ANALYZER
R5
)
)
2
n
GAIN = 10,000
V
)
S
TO SPECTRUM ANALYZER
= ±15V
e
e
OUT
nOUT