LM124D STMicroelectronics, LM124D Datasheet - Page 11

• Manufacturer Part Number: LM124D
• Description: IC OPAMP QUAD LOW POWER 14-SOIC
• Manufacturer: STMicroelectronics

Specifications of LM124D

• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Slew Rate: 0.4 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 20nA
• Voltage - Input Offset: 2000µV
• Current - Supply: 1.5mA
• Current - Output / Channel: 70mA
• Voltage - Supply, Single/dual (±): 3 V ~ 30 V, ±1.5 V ~ 15 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Channels: 4
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 5 mV
• Input Bias Current (max): 150 nA
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 1.2 mA
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Dual Supply Voltage: +/- 3 V, +/- 5 V, +/- 9 V, +/- 12 V
• Maximum Dual Supply Voltage: +/- 15 V
• Minimum Dual Supply Voltage: +/- 1.5 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 30 V
• Supply Voltage (min): 3 V
• Technology: Bipolar
• Voltage Gain Db: 100 dB
• Bandwidth: 1.3 MHz
• Channel Separation: 120
• Common Mode Rejection Ratio: 80
• Current, Input Bias: 20 nA
• Current, Input Offset: 2 nA
• Current, Output: 40 mA
• Current, Supply: 1.5 mA
• Harmonic Distortion: 0.015 %
• Number Of Amplifiers: Quad
• Package Type: SO-14
• Power Dissipation: 50 mW
• Signal Gain: 100 V/mV
• Temperature, Operating, Range: -55 to +125 °C
• Voltage, Input: 32 V
• Voltage, Noise: 40 nV/sqrt Hz
• Voltage, Offset: 2 mV
• Voltage, Output, High: 28 V
• Voltage, Output, Low: 5 mV
• Voltage, Supply: 3 to 30 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-2969-5

LM124, LM224, LM324
5
Note:
Macromodels
Please consider the following before using this macromodel:
All models are a trade-off between accuracy and complexity (i.e. simulation time).
Macromodels are not a substitute to breadboarding; rather, they confirm the validity of a
design approach and help to select surrounding component values.
A macromodel emulates the nominal performance of a typical device within specified
operating conditions (temperature, supply voltage, etc.). Thus the macromodel is often not
as exhaustive as the datasheet, its purpose is to illustrate the main parameters of the
product.
Data derived from macromodels that is used outside of the specified conditions (V
temperature, etc.) or even worse, outside of the device operating conditions (V
is not reliable in any way.
** Standard Linear Ics Macromodels, 1993.
** CONNECTIONS :
* 1 INVERTING INPUT
* 2 NON-INVERTING INPUT
* 3 OUTPUT
* 4 POSITIVE POWER SUPPLY
* 5 NEGATIVE POWER SUPPLY
.SUBCKT LM124 1 3 2 4 5
*******************************************************
.MODEL MDTH D IS=1E-8 KF=3.104131E-15 CJO=10F
* INPUT STAGE
CIP 2 5 1.000000E-12
CIN 1 5 1.000000E-12
EIP 10 5 2 5 1
EIN 16 5 1 5 1
RIP 10 11 2.600000E+01
RIN 15 16 2.600000E+01
RIS 11 15 2.003862E+02
DIP 11 12 MDTH 400E-12
DIN 15 14 MDTH 400E-12
VOFP 12 13 DC 0
VOFN 13 14 DC 0
IPOL 13 5 1.000000E-05
CPS 11 15 3.783376E-09
DINN 17 13 MDTH 400E-12
VIN 17 5 0.000000e+00
DINR 15 18 MDTH 400E-12
VIP 4 18 2.000000E+00
FCP 4 5 VOFP 3.400000E+01
FCN 5 4 VOFN 3.400000E+01
FIBP 2 5 VOFN 2.000000E-03
FIBN 5 1 VOFP 2.000000E-03
* AMPLIFYING STAGE
FIP 5 19 VOFP 3.600000E+02
FIN 5 19 VOFN 3.600000E+02
Doc ID 2156 Rev 6
Macromodels
cc
, V
cc
icm
,
, etc.)
11/19