LM833N/NOPB National Semiconductor, LM833N/NOPB Datasheet - Page 8

• Manufacturer Part Number: LM833N/NOPB
• Description: IC OP AMP DUAL AUDIO 8-DIP
• Manufacturer: National Semiconductor

Specifications of LM833N/NOPB

• Amplifier Type: Audio
• Number Of Circuits: 2
• Slew Rate: 7 V/µs
• Gain Bandwidth Product: 15MHz
• Current - Input Bias: 500nA
• Voltage - Input Offset: 300µV
• Current - Supply: 5mA
• Voltage - Supply, Single/dual (±): ±5 V ~ 15 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Bandwidth: 15 MHz
• Common Mode Rejection Ratio: 100
• Current, Input Bias: 500 nA
• Current, Input Offset: 10 nA
• Current, Output: 40 mA
• Current, Supply: 5 mA
• Harmonic Distortion: 0.002 %
• Number Of Amplifiers: Dual
• Package Type: MDIP-8
• Power Dissipation: 500 mW
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 110 dB
• Voltage, Input: 10 to 36 V
• Voltage, Noise: 4.5 nV/sqrt Hz
• Voltage, Offset: 0.3 mV
• Voltage, Output, High: 13.5 V
• Voltage, Output, Low: -13.5 V
• Voltage, Supply: ±15 V
• No. Of Channels: 2
• Supply Voltage Range: 10V To 36V
• Load Impedance: 2kohm
• Operating Temperature Range: -40°C To +85°C
• Amplifier Case Style: DIP
• No. Of Pins: 8
• Msl: MSL 1 - Unlimited
• Rohs Compliant: Yes
• Number Of Channels: 2
• Voltage Gain Db: 110 dB
• Common Mode Rejection Ratio (min): 80 dB
• Input Offset Voltage: 5 mV at +/- 15 V
• Supply Current: 8 mA at +/- 15 V
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 85 C
• Maximum Dual Supply Voltage: +/- 18 V
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Current - Output / Channel: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device
• Other names: *LM833N; *LM833N/NOPB; LM833; LM833NNS

www.national.com
Typical Performance Characteristics
Application Hints
The LM833 is a high speed op amp with excellent phase
margin and stability. Capacitive loads up to 50 pF will cause
little change in the phase characteristics of the amplifiers
and are therefore allowable.
Capacitive loads greater than 50 pF must be isolated from
the output. The most straightforward way to do this is to put
Complete shielding is required to prevent induced pick up from external sources. Always check with oscilloscope for power line noise.
Inverting Amp
Input Referred Noise Voltage: e
Total Gain: 115 dB
00521826
8
(Continued)
a resistor in series with the output. This resistor will also
prevent excess power dissipation if the output is accidentally
shorted.
Noise Measurement Circuit
@
f = 1 kHz
n
= V0/560,000 (V)
00521827