MAX492CSA+ Maxim Integrated Products, MAX492CSA+ Datasheet - Page 13
![IC OPAMP DUAL R-R 500KHZ 8-SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
MAX492CSA+
Manufacturer Part Number
MAX492CSA+
Description
IC OPAMP DUAL R-R 500KHZ 8-SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX495CPA.pdf
(17 pages)
Specifications of MAX492CSA+
Amplifier Type
General Purpose
Number Of Circuits
2
Output Type
Rail-to-Rail
Slew Rate
0.2 V/µs
Gain Bandwidth Product
500kHz
Current - Input Bias
25nA
Voltage - Input Offset
200µV
Current - Supply
150µA
Current - Output / Channel
30mA
Voltage - Supply, Single/dual (±)
2.7 V ~ 6 V, ±1.35 V ~ 3 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Number Of Channels
2
Common Mode Rejection Ratio (min)
74 dB
Input Offset Voltage
0.5 mV
Input Bias Current (max)
60 nA
Operating Supply Voltage
3 V, 5 V
Supply Current
150 uA
Maximum Power Dissipation
471 mW
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Maximum Dual Supply Voltage
+/- 3 V
Minimum Dual Supply Voltage
+/- 1.35 V
Mounting Style
SMD/SMT
Shutdown
No
Supply Voltage (max)
6 V
Supply Voltage (min)
2.7 V
Voltage Gain Db
104 dB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
in series with IN-, IN+, or both. Series resistors are not
recommended for amplifier applications, as they may
increase input offsets and decrease amplifier bandwidth.
Even with their low quiescent current of less than 150µA
per op amp, the MAX492/MAX494/MAX495 are well
suited for driving loads up to 1kΩ while maintaining DC
accuracy. Stability while driving heavy capacitive loads
is another key advantage over comparable CMOS rail-
to-rail op amps.
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
Figure 6. MAX492 Voltage Follower with 1000pF Load
(R
Figure 7a. MAX492 Voltage Follower with 500pF Load—
R
12
L
L
= 5k Ω
= ∞ )
______________________________________________________________________________________
Output Loading and Stability
10 s/div
10 s/div
V
50mV/div
V
50mV/div
V
50mV/div
V
50mV/div
IN
OUT
IN
OUT
In op amp circuits, driving large capacitive loads
increases the likelihood of oscillation. This is especially
true for circuits with high loop gains, such as a unity-
gain voltage follower. The output impedance and a
capacitive load form an RC network that adds a pole to
the loop response and induces phase lag. If the pole
frequency is low enough—as when driving a large
capacitive load—the circuit phase margin is degraded,
leading to either an under-damped pulse response or
oscillation.
Figure 7b. MAX492 Voltage Follower with 500pF Load—
R
Figure 7c. MAX492 Voltage Follower with 500pF Load—
R
L
L
= 20k Ω
= ∞
10 s/div
10 s/div
V
50mV/div
V
50mV/div
V
50mV/div
V
50mV/div
IN
OUT
IN
OUT