MCP6294-E/P Microchip Technology, MCP6294-E/P Datasheet

Page 1

... B. The CS input puts the device in a Low-power mode. The MCP6291/2/3/4/5 family operates over the Extended Temperature Range of -40°C to +125°C. It also has a power supply range of 2.4V to 5.5V. MCP6291 MCP6291R SOT-23-5 SOT-23 OUT – MCP6294 PDIP, SOIC, TSSOP OUTA INA INA V – ...

Page 2

... (Note µV/° -40°C to +125° (Note (Note Note +85°C (Note +125°C (Note Note 3 ||pF Note 3 ||pF Note -0.3V to 2.5V -0.3V to 5.3V 0. – 0.2V, OUT (Note -40°C to +125° 100 – 100 mV and  2004 Microchip Technology Inc. ...

Page 3

... Thermal Resistance, 5L-SOT-23 Thermal Resistance, 6L-SOT-23 Thermal Resistance, 8L-PDIP Thermal Resistance, 8L-SOIC Thermal Resistance, 8L-MSOP Thermal Resistance, 14L-PDIP Thermal Resistance, 14L-SOIC Thermal Resistance, 14L-TSSOP Note: The Junction Temperature (T J  2004 Microchip Technology Inc. MCP6291/2/3/4/5 = +25° +2.4V to +5.5V pF. L Sym Min Typ ...

Page 4

... ON — 0.01 — OFF — 0.6 — HYST ). OFF Hi-Z -0.7 µA (typ.) 0.7 µA (typ.) = GND, SS Units Conditions V µ µ µ µ µs CS Low 0 OUT 5.0V DD µs CS High OUT  2004 Microchip Technology Inc. ...

Page 5

... T = +85°C A 100 T = +125° -0.5 0.0 0.5 1.0 1.5 2.0 Common Mode Input Voltage (V) FIGURE 2-3: Input Offset Voltage vs. Common Mode Input Voltage  2004 Microchip Technology Inc. MCP6291/2/3/4/5 = +2.4V to +5.5V GND 25% 840 Samples -40°C to +125°C 20% A 15% 10 FIGURE 2-4: ...

Page 6

... Ambient Temperature (°C) Input Bias, Input Offset CMRR PSRR - 100 125 Ambient Temperature (°C) CMRR, PSRR vs. Ambient = +125°C = 5.5V Input Bias Current Input Offset Current Common Mode Input Voltage (V) Input Bias, Offset Currents  2004 Microchip Technology Inc. ...

Page 7

... Frequency (Hz) FIGURE 2-14: Open-Loop Gain, Phase vs. Frequency 5. 2. 0.1 1k 10k 100k 1M Frequency (Hz) FIGURE 2-15: Maximum Output Voltage Swing vs. Frequency.  2004 Microchip Technology Inc. MCP6291/2/3/4/5 = +2.4V to +5.5V GND 1000 100 T = +125° +85° +25° -40° 4.0 4 ...

Page 8

... FIGURE 2-22: vs. Common Mode Input Voltage at 10 kHz. 140 130 120 110 100 4.0 4.5 5.0 5.5 1 FIGURE 2-23: Separation vs. Frequency (MCP6292, MCP6294 and MCP6295 only). 1 2.4V DD 1.4 Op Amp turns on 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.0 0.5 ...

Page 9

... Output High-Z 0.0 0.E+00 5.E-06 1.E-05 2.E-05 2.E-05 3.E-05 3.E-05 Time (5 µs/div) FIGURE 2-27: Chip Select (CS) to Amplifier Output Response Time at V (MCP6293 and MCP6295 only).  2004 Microchip Technology Inc. MCP6291/2/3/4/5 = +2.4V to +5.5V GND 5 +1V/V 4 5.0V DD 4.0 3.5 3.0 2 ...

Page 10

... PIN FUNCTION TABLE FOR SINGLE OP AMPS MCP6291 (PDIP, MCP6291 MCP6271R SOIC, (SOT-23-5) (SOT-23-5) MSOP — — — 1,5,8 — — TABLE 3-2: PIN FUNCTION TABLE FOR DUAL AND QUAD OP AMPS MCP6292 MCP6294 MCP6295 1 1 — — — 8 — — 9 — — 10 — 4 ...

Page 11

... V + 0.3V) can cause excessive SS DD current to flow into or out of the input pins. Current beyond ±2 mA can cause reliability problems. Applica- tions that exceed this rating must be externally limited with a resistor, as shown in Figure 4-2.  2004 Microchip Technology Inc. MCP6291/2/3/4/5 CMOS ...

Page 12

... An example of this type of layout is shown in Figure 4- – OUTA INB INB OUTB A MCP6295 5 CS Cascaded Gain Amplifier pF, as – 300 mV and SS and V (20 mV from the rails with – 20 mV. DD for single supply) should have a local difference would  2004 Microchip Technology Inc. ...

Page 13

... PCB surface. b. Connect the guard ring to the inverting input pin (V –). This biases the guard ring to the IN common mode input voltage.  2004 Microchip Technology Inc. MCP6291/2/3/4/5 4.8 Application Circuits V SS 4.8.1 MULTIPLE FEEDBACK LOW-PASS ...

Page 14

... Op amp B can be used for additional gain unity- gain buffer to isolate the load from the difference amplifier. V OUTB IN2 Load IN1 R 1 FIGURE 4-11 OSB OUT A MCP6295 CS Cascaded Gain Circuit Difference Amplifier OUT A MCP6295 CS Difference Amplifier Circuit.  2004 Microchip Technology Inc. ...

Page 15

... B A MCP6295 CS FIGURE 4-13: Integrator Circuit with Active Compensation.  2004 Microchip Technology Inc. MCP6291/2/3/4/5 4.8.3.6 Second-Order MFB Low-Pass Filter with an Extra Pole-Zero Pair Figure 4- second-order multiple feedback low- pass filter with Chip Select. Use the FilterLab from Microchip to determine the R and C values for the op amp A’ ...

Page 16

... It also outputs the filter circuit in SPICE format, which can be used with the macro model to simulate actual filter performance. macro model for the Software from our web site at  2004 Microchip Technology Inc. ...

Page 17

... Standard marking consists of Microchip part number, year code, week code, traceability code (facility code, mask rev#, and assembly code). For marking beyond this, certain price adders apply. Please check with your Microchip Sales Office.  2004 Microchip Technology Inc. MCP6291/2/3/4/5 Device ...

Page 18

... Package Marking Information (Continued) 14-Lead PDIP (300 mil) (MCP6294) XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 14-Lead SOIC (150 mil) (MCP6294) XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6294) XXXXXX YYWW NNN DS21812D-page 18 Example: MCP6294-E/P 0436256 Example: MCP6294ESL 0436256 Example: 6294EST 0436 256  2004 Microchip Technology Inc. ...

Page 19

... Mold Draft Angle Top Mold Draft Angle Bottom *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side. EIAJ Equivalent: SC-74A Drawing No. C04-091  2004 Microchip Technology Inc. MCP6291/2/3/4 φ ...

Page 20

... A2 MILLIMETERS NOM MAX 6 0.95 1.90 0.90 1.18 1.45 0.90 1.10 1.30 0.00 0.08 0.15 2.60 2.80 3.00 1.50 1.63 1.75 2.80 2.95 3.10 0.35 0.45 0. 0.09 0.15 0.20 0.35 0.43 0.  2004 Microchip Technology Inc. ...

Page 21

... Mold Draft Angle Top Mold Draft Angle Bottom *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-187 Drawing No. C04-111  2004 Microchip Technology Inc. MCP6291/2/3/4 φ A1 ...

Page 22

... L p MILLIMETERS MIN NOM MAX 8 2.54 3.56 3.94 4.32 2.92 3.30 3.68 0.38 7.62 7.94 8.26 6.10 6.35 6.60 9.14 9.46 9.78 3.18 3.30 3.43 0.20 0.29 0.38 1.14 1.46 1.78 0.36 0.46 0.56 7.87 9.40 10.  2004 Microchip Technology Inc. ...

Page 23

... Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-057  2004 Microchip Technology Inc. MCP6291/2/3/4 ...

Page 24

... L p MILLIMETERS MIN NOM MAX 14 2.54 3.56 3.94 4.32 2.92 3.30 3.68 0.38 7.62 7.94 8.26 6.10 6.35 6.60 18.80 19.05 19.30 3.18 3.30 3.43 0.20 0.29 0.38 1.14 1.46 1.78 0.36 0.46 0.56 7.87 9.40 10.  2004 Microchip Technology Inc. ...

Page 25

... Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-065  2004 Microchip Technology Inc. MCP6291/2/3/4 ...

Page 26

... B1 .007 .010 .012 MILLIMETERS* MIN NOM MAX 14 0.65 1.10 0.85 0.90 0.95 0.05 0.10 0.15 6.25 6.38 6.50 4.30 4.40 4.50 4.90 5.00 5.10 0.50 0.60 0. 0.09 0.15 0.20 0.19 0.25 0.  2004 Microchip Technology Inc. ...

Page 27

... Added Section 3.0 “Pin Descriptions”. 4. Corrected application circuits (Section 4.8 “Application Circuits”). 5. Added SOT-23-5 and SOT-23-6 packages and corrected package marking (Section 6.0 “Packaging Information”). 6. Added Appendix A: Revision History.  2004 Microchip Technology Inc. MCP6291/2/3/4/5 information DS21812D-page 27 ...

Page 28

... MCP6291/2/3/4/5 NOTES: DS21812D-page 28  2004 Microchip Technology Inc. ...

Page 29

... Extended Temperature, 8LD MSOP package. c) MCP6293-E/P: Extended Temperature, 8LD PDIP package. d) MCP6293T-E/CH: Tape and Reel, Extended Temperature, 6LD SOT-23 package. a) MCP6294-E/P: Extended Temperature, 14LD PDIP package. b) MCP6294T-E/SL: Tape and Reel, Extended Temperature, 14LD SOIC package. c) MCP6294-E/SL: Extended Temperature, 14LD SOIC package. ...

Page 30

... MCP6291/2/3/4/5 NOTES: DS21812D-page 30  2004 Microchip Technology Inc. ...

Page 31

... PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...

Page 32

... Fax: 65-6334-8850 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Taiwan - Hsinchu Tel: 886-3-572-9526 Fax: 886-3-572-6459  2004 Microchip Technology Inc. EUROPE Austria - Weis Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Ballerup Tel: 45-4450-2828 Fax: 45-4485-2829 France - Massy Tel: 33-1-69-53-63-20 ...