LT1994IMS8#PBF Linear Technology, LT1994IMS8#PBF Datasheet
LT1994IMS8#PBF
Specifications of LT1994IMS8#PBF
Available stocks
Related parts for LT1994IMS8#PBF
LT1994IMS8#PBF Summary of contents
Page 1
... The LT1994 is available in an 8-pin MSOP or 8-pin DFN package. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. 3V 10μF V SD0 ...
Page 2
... LT1994MPDD#PBF LT1994MPDD#TRPBF LT1994CMS8#PBF LT1994CMS8#TRPBF LT1994IMS8#PBF LT1994IMS8#TRPBF Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. *The temperature grade is identifi label on the shipping container. Consult LTC Marketing for information on non-standard lead based fi nish parts. For more information on lead free part marking, go to: For more information on tape and reel specifi ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are 499Ω 800Ω mid-supply voltage (See Figure 1) unless otherwise noted – )/2. V ...
Page 4
LT1994 ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are 499Ω 800Ω mid-supply voltage (See Figure 1) unless otherwise noted – )/2. ...
Page 5
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are 499Ω 800Ω mid-supply voltage (See Figure 1) unless otherwise noted – )/2. V ...
Page 6
LT1994 TYPICAL PERFORMANCE CHARACTERISTICS Differential Input Referred Voltage Offset vs Temperature 500 1. 1.5V OCM 250 FOUR TYPICAL UNITS 0 –250 –500 –750 –50 – TEMPERATURE (°C) ...
Page 7
TYPICAL PERFORMANCE CHARACTERISTICS Input Common Mode Rejection vs Frequency 100 V ICM OSDIFF 10k 100k 1M 10M 100M FREQUENCY (Hz) 1995 G10 Differential ...
Page 8
LT1994 TYPICAL PERFORMANCE CHARACTERISTICS Small-Signal Step Response 25pF LOAD + OUT 0pF LOAD 499Ω 100mV , IN P-P SINGLE ENDED – OUT 20ns/DIV 1994 G18 Supply Current vs ...
Page 9
PIN FUNCTIONS + – (Pins 1, 8): Noninverting and Inverting Input Pins of the Amplifi er, Respectively. For best performance highly recommended that stray capacitance be kept to an absolute minimum by keeping printed circuit ...
Page 10
LT1994 APPLICATIONS INFORMATION Functional Description The LT1994 is a small outline, wideband, low noise and low distortion fully-differential amplifi er with accurate output-phase balancing. The LT1994 is optimized to drive low voltage, single-supply, differential input ana- log-to-digital converters (ADCs). The ...
Page 11
APPLICATIONS INFORMATION General Amplifi er Applications As levels of integration have increased and, correspond- ingly, system supply voltages decreased, there has been a need for ADCs to process signals differentially in order to maintain good signal-to-noise ratios. These ADCs are ...
Page 12
LT1994 APPLICATIONS INFORMATION V is defi ned as the average of the two input voltages, ICM V and V (also called the input common mode INP INM voltage • ICM INP INM ...
Page 13
APPLICATIONS INFORMATION Input Common Mode Voltage Range The LT1994’s input common mode voltage (V as the average of the two input voltages, V – It extends from V to approximately 1.25V below V input common mode range depends on the ...
Page 14
LT1994 APPLICATIONS INFORMATION A plot of this equation and a plot of the noise generated by the feedback components are shown in Figure 6. The LT1994’s input referred voltage noise contributes the equivalent noise of a 560Ω resistor. When the ...
Page 15
APPLICATIONS INFORMATION In general, the die temperature can be estimated from the ambient temperature T , and the device power dis- A sipation • θ The power ...
Page 16
LT1994 APPLICATIONS INFORMATION 0.1μF ceramic capacitor in single-supply applications. This will help prevent thermal noise from the internal 80kΩ-80kΩ voltage divider (25nV/√Hz) and other exter- nal sources of noise from being converted to differential noise due to mismatches in the ...
Page 17
TYPICAL APPLICATIONS Differential 1st Order Lowpass Filter Maximum –3dB frequency (f ) 2MHz 3dB Stopband attenuation: –6dB at 2 • f 3dB C11 R11 R21 – 0.1μ – LT1994 8 0.1μF ...
Page 18
LT1994 TYPICAL APPLICATIONS 3. Calculate R3, R2 and R1 using the standard 5% C2 value, the specifi and the specifi ed passband 3dB gain (Gn) ≤ ≤ MHz and Gain Gain 3 ...
Page 19
PACKAGE DESCRIPTION 3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 0.25 0.05 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. DRAWING ...
Page 20
... LT1994 I 2 OUT 8 0.1μ 1μF 140Ω 1k 82pF 120pF 82pF 1μF 140Ω 0.1μF 120pF 120pF LT1994 Q 2 OUT 8 0.1μ 1μF 140Ω 1k 82pF 1994 TA02 LT 0309 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 1994fb ...