AD8052ARZ Analog Devices Inc, AD8052ARZ Datasheet - Page 18
![IC OPAMP VF R-R DUAL LDIST 8SOIC](/photos/5/66/56684/505-8-soic_sml.jpg)
AD8052ARZ
Manufacturer Part Number
AD8052ARZ
Description
IC OPAMP VF R-R DUAL LDIST 8SOIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD8051ARTZ-REEL7.pdf
(24 pages)
Specifications of AD8052ARZ
Slew Rate
170 V/µs
Amplifier Type
Voltage Feedback
Number Of Circuits
2
Output Type
Rail-to-Rail
-3db Bandwidth
110MHz
Current - Input Bias
1.4µA
Voltage - Input Offset
1800µV
Current - Supply
4.8mA
Current - Output / Channel
45mA
Voltage - Supply, Single/dual (±)
3 V ~ 12 V, ±1.5 V ~ 6 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Op Amp Type
High Speed
No. Of Amplifiers
2
Bandwidth
110MHz
Supply Voltage Range
3V To 12V
Amplifier Case Style
SOIC
No. Of Pins
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Gain Bandwidth Product
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD8052ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD8052ARZ-REEL
Manufacturer:
NXP
Quantity:
1 500
Part Number:
AD8052ARZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD8052ARZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD8052ARZ-REL
Manufacturer:
SANREX1
Quantity:
1
Part Number:
AD8052ARZ-REL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD8051/AD8052/AD8054
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8051/AD8052/
AD8054 requires careful attention to board layout and component
selection. Proper RF design techniques and low parasitic
component selection are necessary.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance path. The ground plane should be removed from the
area near the input pins to reduce parasitic capacitance.
Chip capacitors should be used for supply bypassing. One end
should be connected to the ground plane and the other within
3 mm of each power pin. An additional large (4.7 μF to 10 μF)
tantalum electrolytic capacitor should be connected in parallel,
but not necessarily so close, to supply current for fast, large
signal changes at the output.
The feedback resistor should be located close to the inverting
input pin to keep the parasitic capacitance at this node to a
minimum. Parasitic capacitance of less than 1 pF at the inverting
input can significantly affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than about 25 mm). These should be designed with a
characteristic impedance of 50 Ω or 75 Ω and be properly
terminated at each end.
ACTIVE FILTERS
Active filters at higher frequencies require wider bandwidth op
amps to work effectively. Excessive phase shift produced by
lower frequency op amps can significantly affect active filter
performance.
Figure 46 shows an example of a 2 MHz biquad bandwidth filter
that uses three op amps of an AD8054. Such circuits are
sometimes used in medical ultrasound systems to lower the
Rev. J | Page 18 of 24
noise bandwidth of the analog signal before analog-to-digital
conversion.
Note that the unused amplifier’s inputs should be tied to ground.
V
The frequency response of the circuit is shown in Figure 47.
IN
3kΩ
R1
Figure 47. Frequency Response of 2 MHz Band-Pass Biquad Filter
–10
–20
–30
–40
0
10k
2
3
Figure 46. 2 MHz Biquad Band-Pass Filter Using AD8054
50pF
AD8054
2kΩ
C1
R2
1
2kΩ
R3
100k
6
5
AD8054
1kΩ
2kΩ
FREQUENCY (Hz)
R4
R6
7
1M
2kΩ
R5
10
9
50pF
AD8054
C2
10M
8
13
BAND-PASS
FILTER OUTPUT
12
100M
14