MAX6383XR31D3+T Maxim Integrated Products, MAX6383XR31D3+T Datasheet - Page 6

• Manufacturer Part Number: MAX6383XR31D3+T
• Description: IC MPU/RESET CIRC 3.08V SC70-3
• Manufacturer: Maxim Integrated Products
• Type: Simple Reset/Power-On Resetr

Specifications of MAX6383XR31D3+T

• Number Of Voltages Monitored: 1
• Output: Open Drain or Open Collector
• Reset: Active Low
• Reset Timeout: 140 ms Minimum
• Voltage - Threshold: 3.08V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SC-70-3, SOT-323-3
• Monitored Voltage: 1.8 V to 5 V
• Undervoltage Threshold: 3 V
• Overvoltage Threshold: 3.15 V
• Output Type: Active Low, Open Drain
• Manual Reset: Not Resettable
• Watchdog: No Watchdog
• Battery Backup Switching: No Backup
• Power-up Reset Delay (typ): 280 ms
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1 V
• Supply Current (typ): 7 uA
• Maximum Power Dissipation: 235 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Power Fail Detection: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MAX6383XR31D3+T; MAX6383XR31D3+TTR

A µP reset input starts the µP in a known state. These
µP supervisory circuits assert reset to prevent code
execution errors during power-up, power-down, or
brownout conditions.
Reset asserts when V
once V
keeps the reset output asserted for the reset timeout
period. After this interval, reset output deasserts. Reset
output is guaranteed to be in the correct logic state for
V
Many µP-based products require manual reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic low on MR
asserts reset. Reset remains asserted while MR is low,
and for the reset active timeout period (t
returns high. This input has an internal 63kΩ pullup
resistor (1.56kΩ for MAX6390), so it can be left uncon-
nected if it is not used. MR can be driven with TTL or
CMOS logic levels, or with open-drain/collector outputs.
Connect a normally open momentary switch from MR to
GND to create a manual-reset function; external
debounce circuitry is not required. If MR is driven from
long cables or if the device is used in a noisy environ-
ment, connecting a 0.1µF capacitor from MR to GND
provides additional noise immunity.
RESET IN is compared to an internal +1.27V reference.
If the voltage at RESET IN is less than 1.27V, reset
asserts. Use the RESET IN comparator as a user-
adjustable reset detector or as a secondary power-sup-
ply monitor by implementing a resistor-divider at RESET
IN (shown in Figure 1). Reset asserts when either V
or RESET IN falls below its respective threshold volt-
age. Use the following equation to set the threshold:
where V
tion, choose a value of R2 and calculate R1:
Since the input current at RESET IN is 50nA (max),
large values can be used for R2 with no significant loss
in accuracy.
SC70/µDFN, Single/Dual Low-Voltage,
Low-Power µP Reset Circuits
6
CC
_______________________________________________________________________________________
≥ 1V.
CC
THRST
V
R1 = R2 [(V
exceeds the reset threshold, an internal timer
INTH
= +1.27V. To simplify the resistor selec-
(MAX6387/MAX6388/MAX6389)
Manual Reset Input (MAX6384/
= V
MAX6385/MAX6386/MAX6390)
THRST
INTH
CC
Detailed Description
/V
is below the reset threshold;
(R1/R2 + 1)
RESET IN Comparator
THRST
) - 1]
RESET Output
RP
) after MR
CC
___________Applications Information
In addition to issuing a reset to the µP during power-up,
power-down,
MAX6381–MAX6390 are relatively immune to short dura-
tion negative-going V
The Typical Operating Characteristics section shows the
Maximum Transient Durations vs. Reset Comparator
Overdrive, for which the MAX6381–MAX6390 do not
generate a reset pulse. This graph was generated using
Reset Thresholds (-40°C to +125°C)
SUFFIX
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Negative-Going V
V
and
TH
4.51
4.39
4.27
4.19
4.10
4.00
3.90
3.80
3.71
3.61
3.51
3.41
3.32
3.22
3.12
3.00
2.93
2.85
2.73
2.63
2.56
2.44
2.34
2.26
2.13
2.05
1.95
1.85
1.76
1.62
1.54
(min)
CC
brownout
transients (glitches).
V
TH
4.63
4.50
4.38
4.30
4.20
4.10
4.00
3.90
3.80
3.70
3.60
3.50
3.40
3.30
3.20
3.08
3.00
2.93
2.80
2.70
2.63
2.50
2.40
2.31
2.19
2.10
2.00
1.90
1.80
1.67
1.58
(nom)
conditions,
CC
Transients
V
TH
4.74
4.61
4.48
4.41
4.31
4.20
4.10
4.00
3.90
3.79
3.69
3.59
3.49
3.38
3.28
3.15
3.08
3.00
2.87
2.77
2.69
2.56
2.46
2.37
2.24
2.15
2.05
1.95
1.85
1.71
1.61
(max)
the