MCP102-195I/TO Microchip Technology, MCP102-195I/TO Datasheet
![IC SUPERVISOR 1.95V LOW TO-92](/photos/7/50/75004/to-92_pkg_sml.jpg)
MCP102-195I/TO
Specifications of MCP102-195I/TO
Related parts for MCP102-195I/TO
MCP102-195I/TO Summary of contents
Page 1
... Resets microcontroller in a power-loss event • RST pin (Active-low): - MCP121: Active-low, open-drain - MCP131: Active-low, open-drain with internal pull-up resistor - MCP102 and MCP103: Active-low, push-pull • Reset Delay Timer (120 ms delay, typ.) • Available in SOT23-3, TO-92 and SC-70 packages • Temperature Range: - Extended: -40° ...
Page 2
... T = -40°C to +125°C. A Parameters Operating Voltage Range Specified V Value to RST low DD Operating Current MCP102, MCP103, MCP121 MCP131 Note 1: Trip point is ±1.5% from typical value. 2: Trip point is ±2.5% from typical value. 3: RST output is forced low. There is a current through the internal pull-up resistor. ...
Page 3
... A V Note +25° 500 µ TRIP(MIN mA, For MCP102/MCP103 OH only (push-pull output 5. 3.0V, Time voltage > 5.5V DD applied 100s, current into pin limited to 2 mA, 25°C operation recommended (Note 5, Note 6) µA ). The total time that the OUT pin should be OUT DS21906B-page 3 ...
Page 4
... Detect to RST Inactive DD V Detect to RST Active DD RST Rise Time After RST Active (MCP102 and MCP103 only) Note 1: These parameters are for design guidance only and are not 100% tested. TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise noted, all limits are specified for -40° ...
Page 5
... Temperature DD (Reset Power-up Timer Inactive) (MCP121-450). © 2005 Microchip Technology Inc. MCP102/103/121/131 = 1V to 5.5V 5.5V 14 5. 2.8V 6 2.1V 1. FIGURE 2-4: (Reset Power-up Timer Active) (MCP102-195 FIGURE 2-5: (Reset Power-up Timer Active) (MCP131-315 FIGURE 2-6: (Reset Power-up Timer Active) (MCP121-450). ...
Page 6
... DD 16 MCP102-195 14 +25° Device in Reset Device in Reset t t RPU RPU 6 0° 5.0 6.0 1.0 FIGURE 2-10: (Reset Power-up Timer Active) (MCP102-195). 80 MCP131-315 70 60 Device in Reset 50 t RPU 5.0 6.0 1.0 FIGURE 2-11: (Reset Power-up Timer Active) (MCP131-315). 16 MCP121-450 +70° ...
Page 7
... DD DD 0.045 0.040 0.080 0.035 0.060 0.030 0.025 0.040 0.020 0.020 0.015 0.010 0.000 0.005 0.000 -0.020 140 0.00 FIGURE 2-16: (MCP102-195 @ V 0.070 MCP131-315 0.108 0.060 V DD 0.106 0.050 0.104 0.102 0.040 0.100 0.030 0.098 0.096 0.020 0.094 0.010 0.092 0.000 ...
Page 8
... Temperature (°C) FIGURE 2-21: V vs. Temperature OL (MCP121-450 @ V = 4.1V). DD DS21906B-page 5.5V 2.110 2.090 2.070 2.050 2.030 2.010 = 0.25 mA 1.990 1.970 = 0.00 mA 1.950 80 120 0.00 FIGURE 2-22: (MCP102-195 @ 120 = 120 = 100 k (MCP121 only; PU MCP102-195 ...
Page 9
... FIGURE 2-27: (MCP131-315). 145 140 135 130 125 120 increasing from: 115 110 85 110 -40 FIGURE 2-28: (MCP121-450). = 100 k (MCP121 only; PU MCP102-195 increasing from: DD increasing from increasing DD from 4.0V V increasing DD from 5.5V - 110 Temperature (°C) t vs. Temperature RPU V ...
Page 10
... Temperature (°C) FIGURE 2-31: t vs. Temperature RT (MCP121-450). DS21906B-page 5.5V 1400 MCP102-195 MCP121-450 1200 increasing from: 1000 800 MCP102-195 600 increasing from: 400 MCP131-315 200 0 85 110 0.001 FIGURE 2-32: V (min TRIP 10m 1.00E-02 1m 1.00E-03 100µ 1.00E-04 10µ 1.00E-05 1µ ...
Page 11
... The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE Pin No. MCP102 Symbol MCP121 MCP103 MCP131 1 1 RST Output State Positive power supply Ground reference SS © 2005 Microchip Technology Inc. MCP102/103/121/131 Function Falling: > TRIP < TRIP Rising: > TRIP HYS < TRIP HYS DS21906B-page 11 ...
Page 12
... V SS Note 1: Resistor R may be required with the PU MCP121 due to the open-drain output. Resistor R may not be required with PU the MCP131 due to the internal pull-up resistor. The MCP102 and MCP103 do not require the external pull-up resistor. FIGURE 4-1: Typical Application Circuit TRIPMAX V TRIPMIN ...
Page 13
... Figure 4-3 shows a typical transient duration vs. reset comparator overdrive, for MCP102/103/121/131 will not generate a reset pulse. It shows that the farther below the trip point the transient pulse goes, the duration of the pulse required to cause a reset gets shorter. Figure 2-32 shows the transient response characteristics for the MCP102/103/121/131. A 0.1 µ ...
Page 14
... MCP102/103/121/131 ® 4.4 Using in PICmicro Microcontroller, ICSP™ Applications (MCP121 only) Figure 4-5 shows the typical application circuit for using the MCP121 for voltage superviory function when the PICmicro microcontroller will be programmed via the ICSP feature. Additional information is available in TB087, “Using Voltage Supervisors with PICmicro Microcontroller Systems which Implement In-Circuit Serial Programming™ ...
Page 15
... Microchip Technology Inc. MCP102/103/121/131 Example: MCP102 195I e TO^^ 547256 Example: MCP1xx = Part Number MCP102 MCP103 MCP121 MCP131 MCP1xxT-195I/TT JGNN TGNN MCP1xxT-240ETT JHNN THNN MCP1xxT-270E/TT JJNN TJNN MCP1xxT-300E/TT JKNN TKNN ...
Page 16
... MCP1xxT-270E/LB BJN FJN MCP1xxT-300E/LB BKN FKN MCP1xxT-315E/LB BLN FLN MCP1xxT-450E/LB BMN FMN MCP1xxT-475E/LB BPN FPN Example: MCP1xx = Part Number MCP102 MCP103 MCP121 MCP131 MCP1xxT-195I/LB BGNN FGNN MCP1xxT-240E/LB BHNN FHNN MCP1xxT-270E/LB BJNN FJNN MCP1xxT-300E/LB BKNN FKNN MCP1xxT-315E/LB BLNN FLNN MCP1xxT-450E/LB BMNN FMNN ...
Page 17
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: TO-236 Drawing No. C04-104 © 2005 Microchip Technology Inc. MCP102/103/121/131 Units ...
Page 18
... MCP102/103/121/131 3-Lead Plastic Small Outline Transistor (LB) (SC-70 Number of Pins Pitch Outside lead pitch (basic) Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Foot Length Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom ...
Page 19
... Mold Draft Angle Bottom *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: TO-92 Drawing No. C04-101 © 2005 Microchip Technology Inc. MCP102/103/121/131 Units INCHES* MIN NOM ...
Page 20
... MCP102/103/121/131 5.2 Product Tape and Reel Specifications FIGURE 5-1: EMBOSSED CARRIER DIMENSIONS (8, 12, 16 AND 24 MM TAPE ONLY) Top Cover Tape K 0 TABLE 1: CARRIER TAPE/CAVITY DIMENSIONS Case Package Outline Type TT SOT- SC-70 3L FIGURE 5-2: 3-LEAD SOT-23/SC70 DEVICE TAPE AND REEL SPECIFICATIONS Device ...
Page 21
... FIGURE 5-3: TO-92 DEVICE TAPE AND REEL SPECIFICATIONS Device Marking MARK MARK FACE FACE Seal Tape Back Tape Note: Bent leads are for Tape and Reel only. © 2005 Microchip Technology Inc. MCP102/103/121/131 User Direction of Feed P MARK FACE W DS21906B-page 21 ...
Page 22
... MCP102/103/121/131 NOTES: DS21906B-page 22 © 2005 Microchip Technology Inc. ...
Page 23
... Added Figure 2-33. 4. Updated SC-70 package markings and added Pb-free marking information to Section 5.0 “Packaging information”. 5. Added Appendix A: “Revision History”. Revision A (August 2004) • Original Release of this Document. © 2005 Microchip Technology Inc. MCP102/103/121/131 Applications (for ICSP DS21906B-page 23 ...
Page 24
... MCP102/103/121/131 NOTES: DS21906B-page 24 © 2005 Microchip Technology Inc. ...
Page 25
... Tape/Reel Temperature Monitoring Range Option Options Device: MCP102: MicroPower Voltage Supervisor, push-pull MCP102T: MicroPower Voltage Supervisor, push-pull (Tape and Reel) MCP103: MicroPower Voltage Supervisor, push-pull MCP103T: MicroPower Voltage Supervisor, push-pull (Tape and Reel) MCP121 MicroPower Voltage Supervisor, open-drain MCP121T: MicroPower Voltage Supervisor, open-drain ...
Page 26
... MCP102/103/121/131 NOTES: DS21906B-page 26 © 2005 Microchip Technology Inc. ...
Page 27
... PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance and WiperLock are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 28
... Fax: 65-6334-8850 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Taiwan - Hsinchu Tel: 886-3-572-9526 Fax: 886-3-572-6459 © 2005 Microchip Technology Inc. EUROPE Austria - Weis Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Ballerup Tel: 45-4450-2828 Fax: 45-4485-2829 France - Massy Tel: 33-1-69-53-63-20 ...