MAX16048ETN+ Maxim Integrated Products, MAX16048ETN+ Datasheet - Page 28

• Manufacturer Part Number: MAX16048ETN+
• Description: IC EE-PROG SYS MGR 8CH 56-TQFN
• Manufacturer: Maxim Integrated Products
• Type: System Managerr

Specifications of MAX16048ETN+

• Number Of Voltages Monitored: 8
• Output: Open Drain, Push-Pull
• Reset: Active Low
• Reset Timeout: Adjustable/Selectable
• Voltage - Threshold: Adjustable/Selectable
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 56-TQFN
• Manual Reset: Resettable
• Watchdog: Yes
• Supply Voltage (max): 14 V
• Supply Voltage (min): 3 V
• Supply Current (typ): 6500 uA
• Maximum Power Dissipation: 3810 mW
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
EN_OUT1–EN_OUT6 can act as high-voltage charge-
pump outputs to drive up to six external n-channel
MOSFETs. During sequencing, an EN_OUT_ output
configured this way drives 6µA until the voltage reach-
es 5V above the corresponding MON_ to fully enhance
the external n-channel MOSFET. For example,
EN_OUT2 will rise to 5V above MON2. See the
Sequencing section for more detailed information on
power-supply sequencing.
EN_OUT1–EN_OUT4 can operate in closed-loop track-
ing mode. When configured for closed-loop tracking,
EN_OUT1–EN_OUT4 are capable of driving the gates
of up to four external n-channel MOSFETs. For closed-
loop tracking, configure GPIO1–GPIO4 as return-sense
line inputs (INS_) to be used in conjunction with
EN_OUT1–EN_OUT4 and MON1–MON4. See the
Closed-Loop Tracking section.
Table 9. EN_OUT1–EN_OUT12 Configuration (continued)
* MAX16046 only
28
REGISTER/EEPROM
______________________________________________________________________________________
ADDRESS
22h
Closed-Loop Tracking Operation
Charge-Pump Configuration
RANGE
[1:0]
[3:2]
[5:4]
[7:6]
BIT
EN_OUT10 Configuration*:
00 = EN_OUT10 is an open-drain active-low output
01 = EN_OUT10 is an open-drain active-high output
10 = EN_OUT10 is a push-pull active-low output
11 = EN_OUT10 is a push-pull active-high output
EN_OUT11 Configuration*:
00 = EN_OUT11 is an open-drain active-low output
01 = EN_OUT11 is an open-drain active-high output
10 = EN_OUT11 is a push-pull active-low output
11 = EN_OUT11 is a push-pull active-high output
EN_OUT12 Configuration*:
00 = EN_OUT12 is an open-drain active-low output
01 = EN_OUT12 is an open-drain active high output
10 = EN_OUT12 is a push-pull active-low output
11 = EN_OUT12 is a push-pull active-high output
Reserved
Connect an external pullup resistor from the output to
an external voltage up to 6V (abs max, EN_OUT7 to
EN_OUT12) or 12V (abs max, EN_OUT1 to EN_OUT6)
when configured as an open-drain output. Choose the
pullup resistor depending on the number of devices
connected to the open-drain output and the allowable
current consumption. The open-drain output configura-
tion allows wire-ORed connection.
The MAX16046/MAX16048s’ programmable outputs
sink 2mA and source 100µA when configured as push-
pull outputs.
When V
voltage, the EN_OUT_ output is high impedance until
V
its configured deasserted state. See Figures 3 and 4.
RESET is configured as an active-low open-drain output
pulled up to V
and 4.
CC
is approximately 2.4V and then EN_OUT_ will be in
CC
DESCRIPTION
is ramped from 0V to the operating supply
CC
through a 10kΩ resistor for Figures 3
Open-Drain Output Configuration
EN_OUT_ State During Power-Up
Push-Pull Output Configuration