MAX6887LETE+ Maxim Integrated Products, MAX6887LETE+ Datasheet - Page 9
![IC SUPERVISOR HEX 16-TQFN](/photos/6/66/66627/16-tqfn_21-0140l_sml.jpg)
MAX6887LETE+
Manufacturer Part Number
MAX6887LETE+
Description
IC SUPERVISOR HEX 16-TQFN
Manufacturer
Maxim Integrated Products
Type
Multi-Voltage Supervisorr
Datasheet
1.MAX6887QETE.pdf
(13 pages)
Specifications of MAX6887LETE+
Number Of Voltages Monitored
6
Output
Open Drain or Open Collector
Reset
Active Low
Reset Timeout
180 ms Minimum
Voltage - Threshold
6 Selectable Threshold Combinations
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TQFN Exposed Pad
Undervoltage Threshold
2.88 V, 2.19 V, 1.58 V, 1.31 V, 0.557 V, 0.557 V
Manual Reset
Resettable
Watchdog
Watchdog
Supply Voltage (max)
5.8 V
Supply Voltage (min)
2.7 V
Supply Current (typ)
900 uA
Maximum Power Dissipation
1667 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
existing state while system-level testing occurs. Leave
MARGIN unconnected or connect to BP if unused. An
internal 10µA current source pulls MARGIN to BP.
MARGIN overrides MR if both are asserted at the
same time. The state of RESET, OV, and WDO does not
change while MARGIN = GND.
The MAX6887/MAX6888 feature three active-low open-
drain outputs: RESET, OV, and WDO. After power-up or
overvoltage/undervoltage conditions, RESET and OV
remain in their active states until their timeout periods
expire and no undervoltage/overvoltage conditions are
present (see Figure 2).
OV asserts when any monitored input is above its over-
voltage threshold and remains asserted until all inputs
are below their thresholds and its respective 25µs time-
out period expires. Connect OV to MR to bring RESET
low during an overvoltage condition. OV requires a
pullup resistor (unless connected to MR).
Table 2. MAX6888 Threshold Options
MAX6888AETE
MAX6888BETE
MAX6888CETE
MAX6888DETE
MAX6888EETE
MAX6888FETE
MAX6888GETE
MAX6888HETE
MAX6888QETE
MAX6888IETE
MAX6888JETE
MAX6888KETE
MAX6888LETE
MAX6888METE
MAX6888NETE
MAX6888OETE
MAX6888PETE
MAX6888RETE
Hex/Quad, Power-Supply Supervisory Circuits
PART
RESET , OV , and WDO Outputs
_______________________________________________________________________________________
4.620
4.620
4.620
3.060
3.060
3.060
3.060
3.060
0.557
4.380
4.380
4.380
2.880
2.880
2.880
2.880
2.880
0.527
IN1
UV THRESHOLDS (V)
3.060
3.060
3.060
2.310
2.310
2.310
2.310
1.670
0.557
2.880
2.880
2.880
2.190
2.190
2.190
2.190
1.580
0.527
IN2
2.310
2.310
1.670
1.670
1.670
1.390
0.557
0.557
0.557
2.190
2.190
1.580
1.580
1.580
1.310
0.527
0.527
0.527
IN3
1.670
0.557
0.557
1.390
0.557
0.557
0.557
0.557
0.557
1.580
0.527
0.527
1.310
0.527
0.527
0.527
0.527
0.527
RESET asserts when any monitored input is below its
undervoltage threshold or MR is asserted. RESET
remains asserted for 200ms after all assertion-causing
conditions have been cleared. Configure RESET to
assert when the watchdog timer expires by connecting
WDO to MR. RESET requires a pullup resistor.
WDO asserts when the watchdog timer expires. See
the Configuring the Watchdog Timer section for a com-
plete description. WDO requires a pullup resistor.
A watchdog timer monitors microprocessor (µP) soft-
ware execution for a stalled condition and resets the µP
if it stalls. Connect the watchdog timer output WDO to
the reset input or a nonmaskable interrupt of the µP.
The watchdog timer features independent initial and
normal watchdog timeout periods of 102.4s and 1.6s,
respectively.
IN4
5.360
5.360
5.360
3.540
3.540
3.540
3.540
3.540
0.643
5.620
5.620
5.620
3.700
3.700
3.700
3.700
3.700
0.673
IN1
Configuring the Watchdog Timer
OV THRESHOLDS (V)
3.540
3.540
3.540
2.680
2.680
2.680
1.930
3.700
3.700
3.700
2.810
2.810
2.020
0.673
2.680
0.643
2.810
2.810
IN2
2.680
2.680
1.930
1.930
1.930
1.610
0.643
0.643
0.643
2.810
2.810
2.020
2.020
2.020
1.680
0.673
0.673
0.673
IN3
1.930
0.643
0.643
1.610
0.643
0.643
0.643
0.643
0.643
2.020
0.673
0.673
1.680
0.673
0.673
0.673
0.673
0.673
IN4
9