LP3991TL-2.8/NOPB National Semiconductor, LP3991TL-2.8/NOPB Datasheet - Page 9
![IC VREG 300MA 2.8V 4MICROSMD](/photos/12/65/126587/tla04zta_sml.jpg)
LP3991TL-2.8/NOPB
Manufacturer Part Number
LP3991TL-2.8/NOPB
Description
IC VREG 300MA 2.8V 4MICROSMD
Manufacturer
National Semiconductor
Series
PowerWise®r
Datasheet
1.LP3991TL-1.2EV.pdf
(12 pages)
Specifications of LP3991TL-2.8/NOPB
Regulator Topology
Positive Fixed
Voltage - Output
2.8V
Voltage - Input
Up to 4V
Voltage - Dropout (typical)
0.075V @ 300mA
Number Of Regulators
1
Current - Output
300mA (Min)
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
4-MicroSMD
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
4 V
Output Voltage
2.8 V
Output Type
Fixed
Dropout Voltage (max)
0.08 V at 150 mA
Output Current
0.3 A
Voltage Regulation Accuracy
+/- 1 %
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
For Use With
LP3991TL-1.8EV - BOARD EVALUATION LP3991TL-1.8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Details
Other names
LP3991TL-2.8TR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LP3991TL-2.8/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Application Information
EXTERNAL CAPACITORS
In common with most regulators, the LP3991 requires exter-
nal capacitors for regulator stability. The LP3991 is specifi-
cally designed for portable applications requiring minimum
board space and smallest components. These capacitors
must be correctly selected for good performance.
INPUT CAPACITOR
An input capacitor is required for stability. It is recommended
that a 1.0µF capacitor be connected between the LP3991 in-
put pin and ground (this capacitance value may be increased
without limit).
This capacitor must be located a distance of not more than
1cm from the input pin and returned to a clean analogue
ground. Any good quality ceramic, tantalum, or film capacitor
may be used at the input.
Important: Tantalum capacitors can suffer catastrophic fail-
ures due to surge current when connected to a low-
impedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must
be guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
There are no requirements for the ESR (Equivalent Series
Resistance) on the input capacitor, but tolerance, tempera-
ture, and voltage coefficients must be considered when se-
lecting the capacitor to ensure the capacitance will remain
1.0µF over the entire operating temperature range.
OUTPUT CAPACITOR
Correct selection of the output capacitor is critical to ensure
stable operation in the intended application.
The output capacitor must meet all the requirements specified
in the recommended capacitor table over all conditions in the
application. these conditions include DC bias, frequency and
temperature. Unstable operation will result if the capacitance
drops below the minimum specified value.
The LP3991 is designed specifically to work with very small
ceramic output capacitors. For voltage options of 1.5V and
higher, A 4.7µF ceramic capacitor (dielectric type X7R or
X5R) with an ESR between 5mΩ to 500mΩ, is suitable in the
LP3991 application circuit. However, on lower V
2.2µF may be employed with only a small increase in load
transient.
Other ceramic types such as Y5V and Z5U are less suitable
owing to their inferior temperature characteristics. (See sec-
tion on Capacitor Characteristics).
It is also recommended that the output capacitor is placed
within 1cm of the output pin and returned to a clean, low
impedance, ground connection.
It is possible to use tantalum or film capacitors at the device
output, V
size and cost (see the section Capacitor Characteristics).
NO-LOAD STABILITY
The LP3991 will remain stable and in regulation with no ex-
ternal load. This is an important consideration in some cir-
cuits, for example CMOS RAM keep-alive applications.
CAPACITOR CHARACTERISTICS
The LP3991 is designed to work with ceramic capacitors on
the input and output to take advantage of the benefits they
offer. For capacitance values around 4.7µF, ceramic capaci-
OUT
, but these are not as attractive for reasons of
OUT
options a
≊
9
tors give the circuit designer the best design options in terms
of low cost and minimal area.
For both input and output capacitors, careful interpretation of
the capacitor specification is required to ensure correct device
operation. The capacitor value can change greatly dependant
on the conditions of operation and capacitor type.
In particular, to ensure stability, the output capacitor selection
should take account of all the capacitor parameters, to ensure
that the specification is met within the application. Capaci-
tance value can vary with DC bias conditions as well as
temperature and frequency of operation. Capacitor values will
also show some decrease over time due to aging. The ca-
pacitor parameters are also dependant on the particular case
size with smaller sizes giving poorer performance figures in
general.
As an example
comparison of capacitor case sizes in a Capacitance vs. DC
Bias plot. As shown in the graph, as a result of the DC Bias
condition, the capacitance value may drop below the mini-
mum capacitance value given in the recommended capacitor
table. Note that the graph shows the capacitance out of spec
for the 0402 case size capacitor at higher bias voltages. It is
therefore recommended that the capacitor manufacturers'
specifications for the nominal value capacitor are consulted
for all conditions as some capacitor sizes (e.g. 0402) may not
be suitable in the actual application. Ceramic capacitors have
the lowest ESR values, thus making them best for eliminating
high frequency noise. The ESR of a typical 4.7µF ceramic
capacitor is in the range of 20mΩ to 40mΩ, which easily
meets the ESR requirement for stability for the LP3991. The
temperature performance of ceramic capacitors varies by
type. Capacitor type X7R is specified with a tolerance of ±15%
over the temperature range -55°C to +125°C. The X5R has a
similar tolerance over the reduced temperature range of -55°
C to +85°C. Some large value ceramic capacitors (4.7µF) are
manufactured with Z5U or Y5V temperature characteristics,
which can result in the capacitance dropping by more than
50% as the temperature varies from 25°C to 85°C. Therefore
X7R or X5R types are recommended in applications where
the temperature will change significantly above or below 25°
C.
Tantalum capacitors are less desirable than ceramic for use
as output capacitors because they are more expensive when
comparing equivalent capacitance and voltage ratings in the
FIGURE 1. Effect of DC bias on Capacitance Value.
Figure 1
shows a typical graph showing a
www.national.com
20110040