LM1117T-5.0/NOPB National Semiconductor, LM1117T-5.0/NOPB Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM1117T-5.0/NOPB
Manufacturer Part Number
LM1117T-5.0/NOPB
Description
IC REG LDO 800MA 5.0V TO220-3
Manufacturer
National Semiconductor
Datasheet
1.LM1117MPX-5.0NOPB.pdf
(21 pages)
Specifications of LM1117T-5.0/NOPB
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 15V
Voltage - Dropout (typical)
1.2V @ 800mA
Number Of Regulators
1
Current - Output
800mA
Current - Limit (min)
800mA
Operating Temperature
0°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-3 (Straight Leads)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*LM1117T-5.0
LM1117T-5.0
LM1117T-5.0
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM1117T-5.0/NOPB
Manufacturer:
TINS
Quantity:
20 000
www.national.com
Application Note
When the adjustable regulator is used (Figure 3), the best
performance is obtained with the positive side of the resistor
R1 tied directly to the output terminal of the regulator rather
than near the load. This eliminates line drops from appearing
effectively in series with the reference and degrading regu-
lation. For example, a 5V regulator with 0.05Ω resistance
between the regulator and load will have a load regulation
due to line resistance of 0.05Ω x I
nected near the load, the effective line resistance will be
0.05Ω (1+R2/R1) or in this case, it is 4 times worse. In
addition, the ground side of the resistor R2 can be returned
near the ground of the load to provide remote ground sens-
ing and improve load regulation.
4.0 PROTECTION DIODES
Under normal operation, the LM1117 regulators do not need
any protection diode. With the adjustable device, the internal
resistance between the adjust and output terminals limits the
current. No diode is needed to divert the current around the
regulator even with capacitor on the adjust terminal. The
adjust pin can take a transient signal of
the output voltage without damaging the device.
When a output capacitor is connected to a regulator and the
input is shorted to ground, the output capacitor will discharge
into the output of the regulator. The discharge current de-
pends on the value of the capacitor, the output voltage of the
regulator, and rate of decrease of V
lators, the internal diode between the output and input pins
FIGURE 3. Best Load Regulation using Adjustable
FIGURE 2. Typical Application using Fixed Output
Output Regulator
Regulator
(Continued)
L
IN
. If R1 (=125Ω) is con-
. In the LM1117 regu-
±
25V with respect to
10091918
10091919
10
can withstand microsecond surge currents of 10A to 20A.
With an extremely large output capacitor (≥1000 µF), and
with input instantaneously shorted to ground, the regulator
could be damaged.
In this case, an external diode is recommended between the
output and input pins to protect the regulator, as shown in
Figure 4.
5.0 HEATSINK REQUIREMENTS
When an integrated circuit operates with an appreciable
current, its junction temperature is elevated. It is important to
quantify its thermal limits in order to achieve acceptable
performance and reliability. This limit is determined by sum-
ming the individual parts consisting of a series of tempera-
ture rises from the semiconductor junction to the operating
environment. A one-dimensional steady-state model of con-
duction heat transfer is demonstrated in Figure 5. The heat
generated at the device junction flows through the die to the
die attach pad, through the lead frame to the surrounding
case material, to the printed circuit board, and eventually to
the ambient environment. Below is a list of variables that
may affect the thermal resistance and in turn the need for a
heatsink.
Leadframe Size & Material Mounting Pad Size,
No. of Conduction Pins
Die Size
Die Attach Material
Molding Compound Size
and Material
R
FIGURE 4. Regulator with Protection Diode
θ
JC (Component
Variables)
Material, & Location
Placement of Mounting
Pad
PCB Size & Material
Traces Length & Width
Adjacent Heat Sources
Volume of Air
Ambient Temperatue
Shape of Mounting Pad
R
θ
CA (Application
Variables)
10091915