LP38690DT-3.3/NOPB National Semiconductor, LP38690DT-3.3/NOPB Datasheet - Page 5
![IC REG LDO 1A 3.3V TO-252](/photos/12/65/126582/td03b_sml.jpg)
LP38690DT-3.3/NOPB
Manufacturer Part Number
LP38690DT-3.3/NOPB
Description
IC REG LDO 1A 3.3V TO-252
Manufacturer
National Semiconductor
Series
PowerWise®r
Specifications of LP38690DT-3.3/NOPB
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 10V
Voltage - Dropout (typical)
0.65V @ 1A
Number Of Regulators
1
Current - Output
1A
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-252-2, DPak (2 Leads + Tab), TO-252AA, SC-63
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Other names
*LP38690DT-3.3
*LP38690DT-3.3/NOPB
LP38690DT-3.3
*LP38690DT-3.3/NOPB
LP38690DT-3.3
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LP38690DT-3.3/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
e
V
V
I
EN
n
O
EN
Electrical Characteristics
over the full operating temperature range. Unless otherwise specified: V
Min/Max limits are guaranteed through testing, statistical correlation, or design. (Continued)
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not
apply when operating the device outside of its rated operating conditions.
Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink values (if a heatsink is used). The
junction-to-ambient thermal resistance ( θ
area (less than 0.1 square inch). If one square inch of copper is used as a heat dissipator for the TO-252, the θ
package has a θ
to a copper area of one square inch. The θ
(refer to application note AN-1187). If power disspation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown.
Note 3: ESD is tested using the human body model which is a 100pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: Typical numbers represent the most likely parametric norm for 25˚C operation.
Note 5: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground.
Note 6: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Note 7: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from 1mA to full load.
Note 8: Dropout voltage is defined as the minimum input to output differential required to maintain the output within 100mV of nominal value.
Symbol
(LEAK)
J-A
Output Noise
Output Leakage Current
Enable Voltage (LP38692 Only)
Enable Pin Leakage
of approximately 125˚C/W when soldered down to a minimum sized pattern (less than 0.1 square inch) and approximately 70˚C/W when soldered
Parameter
J-A
J-A
) for the TO-252 is approximately 90˚C/W for a PC board mounting with the device soldered down to minimum copper
values for the LLP package are also dependent on trace area, copper thickness, and the number of thermal vias used
Limits in standard typeface are for T
BW = 10Hz to 10kHz
V
V
Output = OFF
Output = ON, V
Output = ON, V
Output = ON, V
V
O
O
EN
= 3.3V
= V
= 0V or 10V, V
O
(NOM) + 1V
Conditions
5
IN
IN
IN
= 4V
= 6V
= 10V
IN
@
= 10V
IN
10V
= V
IN
OUT
J
= 25˚C, and limits in boldface type apply
+ 1V, C
MIN
1.8
3.0
4.0
-1
J-A
IN
drops to approximately 50˚C/W. The SOT-223
= C
(Note 4)
OUT
0.001
TYP
0.7
0.5
= 10 µF, I
MAX
0.4
12
LOAD
1
www.national.com
= 10mA.
µV/
Units
µA
µA
V