MCP1702-1202E/TO Microchip Technology, MCP1702-1202E/TO Datasheet
MCP1702-1202E/TO
Specifications of MCP1702-1202E/TO
Related parts for MCP1702-1202E/TO
MCP1702-1202E/TO Summary of contents
Page 1
... DS00792, Microchip Technology Inc., 2001 © 2009 Microchip Technology Inc. Description The MCP1702 is a family of CMOS low dropout (LDO) voltage regulators that can deliver up to 250 mA of current while consuming only 2.0 µA of quiescent current (typical). The input operating range is specified from 2 ...
Page 2
... MCP1702 Functional Block Diagrams V IN Overcurrent Overtemperature Typical Application Circuits + Battery 1 µF Ceramic DS22008D-page 2 MCP1702 Error Amplifier +V IN Voltage - Reference + GND MCP1702 V OUT GND V OUT V OUT 3.3V I OUT OUT 1 µF Ceramic © 2009 Microchip Technology Inc. ...
Page 3
... The 2.7V (whichever is greater); I DROPOUT(MAX ΔTemperature * OUT-HIGH = lowest voltage measured over the temperature range 2.7V, whichever is greater. OUT(MAX) DROPOUT(MAX) , θ MCP1702 , Note OUT(MAX) DROPOUT(MAX) Conditions Note ≥ 2.5V For V R ≥ 2.7V For V < 2.5V ≥ 2.95V For V < 2.5V, V ...
Page 4
... MCP1702 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise specified, all limits are established for 100 µ µF (X7R µF (X7R), T LOAD OUT IN Boldface type applies for junction temperatures, T Parameters Sym Dropout Voltage V DROPOUT (Note 1, Note 5) Output Delay Time T DELAY Output Noise e N Power Supply Ripple ...
Page 5
... JA θ — 100 — °C/W JC θ — 131.9 — °C/W JA θ — 66.3 — °C θ Exceeding the maximum allowable power MCP1702 Conditions Steady State Transient EIA/JEDEC JESD51-7 FR-4 0.063 4-Layer Board EIA/JEDEC JESD51-7 FR-4 0.063 4-Layer Board DS22008D-page 5 ...
Page 6
... MCP1702 NOTES: DS22008D-page 6 © 2009 Microchip Technology Inc. ...
Page 7
... FIGURE 2-5: Current. 3. 5.0V OUT 2.50 2.00 1.50 +90°C 1.00 0.50 0.00 - FIGURE 2-6: Junction Temperature. MCP1702 = 1 µF Ceramic (X7R 100 µ Temperature = +25° 1.2V OUT 120 160 200 Load Current (mA) Ground Current vs. Load Temperature = +25° 5.0V OUT V = 6.0V ...
Page 8
... MCP1702 Note: Unless otherwise indicated 2.8V +25° OUT(MAX) DROPOUT(MAX) 1.24 1.23 -45°C 0°C 1.22 1.21 1.20 +90°C +25°C 1.19 1. Input Voltage (V) FIGURE 2-7: Output Voltage vs. Input Voltage. 2. 2.8V OUT 2. 0.1 mA LOAD 2.83 +130°C +90°C 2.82 2.81 2.80 2.79 0°C +25°C 2 ...
Page 9
... V = 2.8V OUT +130°C +0°C FIGURE 2-17: 600. 5.0V OUT 500.00 400.00 300.00 200.00 +0°C 100.00 0.00 FIGURE 2-18: Input Voltage. MCP1702 = 1 µF Ceramic (X7R 100 µ Dynamic Line Response. Dynamic Line Response 2.8V OUT R < 0.1 OUT Input Voltage (V) Short Circuit Current vs ...
Page 10
... MCP1702 Note: Unless otherwise indicated 2.8V +25° OUT(MAX) DROPOUT(MAX) 0. 0.15 0.10 0.05 0.00 -0. -0. 10V V = 12V IN IN -0.15 V -0. 1.2V OUT -0. 0 200 mA LOAD -0.30 -45 - Temperature (°C) FIGURE 2-19: Load Regulation vs. Temperature. 0.40 0. 250 mA LOAD 0.20 0.10 0.00 -0.10 -0. -0. 10V IN -0 ...
Page 11
... Output Noise vs. Frequency. © 2009 Microchip Technology Inc. = 2.8V µF Ceramic (X7R), C OUT . 100 1000 FIGURE 2-28: 100 1000 FIGURE 2-29: I =50 mA OUT 100 1000 FIGURE 2-30: MCP1702 = 1 µF Ceramic (X7R 100 µ Power Up Timing. Dynamic Load Response. Dynamic Load Response. DS22008D-page 11 ...
Page 12
... MCP1702 NOTES: DS22008D-page 12 © 2009 Microchip Technology Inc. ...
Page 13
... LDO circuit. For applications that have OUT load currents below 100 mA, the input capacitance requirement can be lowered. The type of capacitor used can be electrolytic. The low ESR characteristics of the ceramic will yield better noise and PSRR performance at high-frequency. MCP1702 Function or battery type. For most ceramic, tantalum or ...
Page 14
... MCP1702 NOTES: DS22008D-page 14 © 2009 Microchip Technology Inc. ...
Page 15
... Figure 4-1). 4.2 Overcurrent The MCP1702 internal circuitry monitors the amount of current flowing through the P-Channel pass transistor. In the event of a short-circuit or excessive output current, the MCP1702 will turn off the P-Channel device for a short period, after which the LDO will attempt to restart ...
Page 16
... MCP1702 NOTES: DS22008D-page 16 © 2009 Microchip Technology Inc. ...
Page 17
... Li-Ion cell batteries. 5.1 Input The input of the MCP1702 is connected to the source of the P-Channel PMOS pass transistor. As with all LDO circuits, a relatively low source impedance (10Ω) is needed to prevent the input impedance from causing the LDO to become unstable ...
Page 18
... MCP1702 NOTES: DS22008D-page 18 © 2009 Microchip Technology Inc. ...
Page 19
... APPLICATION CIRCUITS AND ISSUES 6.1 Typical Application The MCP1702 is most commonly used as a voltage regulator. It’s low quiescent current and low dropout voltage makes it ideal for many battery-powered applications. MCP1702 V GND (2.8V to 3.2V) V OUT V IN 1.8V V OUT I OUT C OUT 150 mA 1 µ ...
Page 20
... P D(MAX) 6.4 Voltage Reference ) x The MCP1702 can be used not only as a regulator, but also as a low quiescent current voltage reference. In many microcontroller applications, the initial accuracy of the reference can be calibrated using production test equipment or by using a ratio measurement. When the initial accuracy is calibrated, the thermal stability and line regulation tolerance are the only errors introduced by the MCP1702 LDO ...
Page 21
... For some applications, there are pulsed load current events that may exceed the specified 250 mA maximum specification of the MCP1702. The internal current limit of the MCP1702 will prevent high peak load demands from causing non-recoverable damage. The 250 mA rating is a maximum average continuous rating ...
Page 22
... MCP1702 NOTES: DS22008D-page 22 © 2009 Microchip Technology Inc. ...
Page 23
... HH 4.0 2.5 HJ 5.0 2.8 — — Custom 4.1 — — Standard Extended Temp Voltage * Symbol Voltage * 1.2 HF 3.0 1.5 HG 3.3 1.8 HH 4.0 2.5 HJ 5.0 2.8 — — MCP1702 Example: HANN Example HA0924 256 Example 1702 1202E e TO^^ 3 924256 DS22008D-page 23 ...
Page 24
... MCP1702 /HDG 3ODVWLF 6PDOO 2XWOLQH 7UDQVLVWRU &% >627 1RWH 1RWHV DS22008D-page © 2009 Microchip Technology Inc. φ ...
Page 25
... Microchip Technology Inc. MCP1702 @ DS22008D-page 25 ...
Page 26
... MCP1702 /HDG 3ODVWLF 7UDQVLVWRU 2XWOLQH 72 >72 1RWH 1RWHV DS22008D-page 26 @ © 2009 Microchip Technology Inc. ...
Page 27
... Page 4: Added junction-to-case information to Temperature Specifications table. 3. Page 16: Updated Package Outline Drawings in Section 7.0 “Packaging Information”. 4. Page 21: Updated Revison History. Page 23: Corrected examples in Product 5. Identification System. Revision A (September 2006) • Original Release of this Document. © 2009 Microchip Technology Inc. OUT second 1% MCP1702 DS22008D-page 27 ...
Page 28
... MCP1702 NOTES: DS22008D-page 28 © 2009 Microchip Technology Inc. ...
Page 29
... To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office PART NO Device Tape Output Feature and Reel Voltage Code Device: MCP1702: 2 µA Low Dropout Positive Voltage Regulator Tape and Reel Tape and Reel Output Voltage *: 12 = 1.2V “Standard” 1.5V “Standard” 1.8V “Standard” 2.5V “ ...
Page 30
... MCP1702 NOTES: DS22008D-page 30 © 2009 Microchip Technology Inc. ...
Page 31
... PICDEM, PICDEM.net, PICtail, PIC Select Mode, Total Endurance, TSHARC, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 32
... Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2009 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...