MCP1702T-5002E/MB Microchip Technology, MCP1702T-5002E/MB Datasheet - Page 10
![IC REG LDO 5V 250MA SOT-89-3](/photos/12/58/125851/c04-029_mb_sml.jpg)
MCP1702T-5002E/MB
Manufacturer Part Number
MCP1702T-5002E/MB
Description
IC REG LDO 5V 250MA SOT-89-3
Manufacturer
Microchip Technology
Specifications of MCP1702T-5002E/MB
Package / Case
SC-62, SOT-89, TO-243 (3 Leads + Tab)
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 13.2V
Voltage - Dropout (typical)
0.33V @ 250mA
Number Of Regulators
1
Current - Output
250mA (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
13.2 V
Output Voltage
5 V
Output Type
Fixed
Dropout Voltage (max)
0.65 V at 250 mA
Output Current
250 mA
Line Regulation
0.1 % / V
Load Regulation
1 %
Voltage Regulation Accuracy
0.4 %
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Primary Input Voltage
5.65V
Output Voltage Fixed
5V
Dropout Voltage Vdo
625mV
No. Of Pins
3
Voltage Regulator Case Style
SOT-89
Operating Temperature Range
-40°C To +125°C
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
GPIODM-KPLCD - BOARD DEMO LCD GPIO EXP KEYPAD
Current - Limit (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
MCP1702T-5002E/MB
MCP1702T-5002E/MBTR
MCP1702T-5002E/MBTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP1702T-5002E/MB
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
MCP1702
3.0
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
3.1
Regulator ground. Tie GND to the negative side of the
output and the negative side of the input capacitor.
Only the LDO bias current (2.0 µA typical) flows out of
this pin; there is no high current. The LDO output
regulation is referenced to this pin. Minimize voltage
drops between this pin and the negative side of the
load.
3.2
Connect V
positive terminal of the output capacitor. The positive
side of the output capacitor should be physically
located as close to the LDO V
The current flowing out of this pin is equal to the DC
load current.
DS22008A-page 10
SOT-23A
Pin No.
1
2
3
–
PIN DESCRIPTIONS
Ground Terminal (GND)
Regulated Output Voltage (V
OUT
to the positive side of the load and the
Pin No.
SOT-89
2, Tab
PIN FUNCTION TABLE
1
3
–
Pin No.
OUT
TO-92
1
3
2
–
pin as is practical.
Symbol
V
OUT
GND
V
NC
OUT
IN
)
Ground Terminal
Regulated Voltage Output
Unregulated Supply Voltage
No connection
3.3
Connect V
Like all LDO linear regulators, low source impedance is
necessary for the stable operation of the LDO. The
amount of capacitance required to ensure low source
impedance will depend on the proximity of the input
source
applications, 1 µF of capacitance will ensure stable
operation of the LDO circuit. For applications that have
load currents below 100 mA, the input capacitance
requirement can be lowered. The type of capacitor
used
electrolytic. The low ESR characteristics of the ceramic
will yield better noise and PSRR performance at high-
frequency.
can
Unregulated Input Voltage Pin
(V
capacitors
IN
IN
be
to the input unregulated source voltage.
)
ceramic,
Function
or
© 2006 Microchip Technology Inc.
battery
tantalum
type.
or
For
aluminum
most