TC1263-2.8VAT Microchip Technology, TC1263-2.8VAT Datasheet - Page 2
![IC CMOS LDO 2.8V 500MA TO220-5](/photos/7/40/74093/to-220-5_straightleads_sml.jpg)
TC1263-2.8VAT
Manufacturer Part Number
TC1263-2.8VAT
Description
IC CMOS LDO 2.8V 500MA TO220-5
Manufacturer
Microchip Technology
Specifications of TC1263-2.8VAT
Regulator Topology
Positive Fixed
Voltage - Output
2.8V
Voltage - Input
Up to 6V
Voltage - Dropout (typical)
0.35V @ 500mA
Number Of Regulators
1
Current - Output
500mA (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
6 V
Output Voltage
2.8 V
Output Type
Fixed
Dropout Voltage (max)
650 mV
Output Current
500 mA
Line Regulation
0.05 %
Load Regulation
0.002 % / mA
Voltage Regulation Accuracy
0.5 %
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
TC12632.8VAT
TC1263
1.0
Absolute Maximum Ratings †
Input Voltage .........................................................6.5V
Output Voltage................ (GND – 0.3V) to (V
Power Dissipation................Internally Limited (Note 7)
Voltage (max.) on Any Pin: (GND – 0.3V) to (V
Operating Temperature Range.... -40°C < T
Storage Temperature..........................-65°C to +150°C
DC CHARACTERISTICS
DS21374C-page 2
Electrical Specifications: Unless otherwise indicated, V
SHDN > V
Input Operating Voltage
Maximum Output Current
Output Voltage
V
Line Regulation
Load Regulation (Note 4)
Dropout Voltage (Note 5)
Supply Current
Shutdown Supply Current
Power Supply Rejection Ratio
Output Short Circuit Current
Thermal Regulation
Output Noise
Note 1:
OUT
Temperature Coefficient
2:
3:
4:
5:
6:
7:
ELECTRICAL
CHARACTERISTICS
IH
Parameters
The minimum V
Regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating
effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal
value measured at a 1.0V differential.
Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
excluding load or line regulation effects. Specifications are for a current pulse equal to I
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction-to-air (i.e., T
dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 “Thermal Considerations” for
more details.
, T
V
TCV
R
A
is the regulator output voltage setting.
= +25°C. Boldface type specifications apply for junction temperatures of -40°C to +125°C.
OUT
=
------------------------------------------------------------------------ -
V
IN
OUTMAX
has to justify the conditions: V
V
OUT
–
V
V
V
V
V
I
V
OUTMAX
OUT
I
OUT
IN
PSRR
I
OUTSC
OUT
OUTMIN
V
Sym
SHDN
OUT
V
I
-V
eN
OUT
DD
IN
/V
/ V
OUT
/ P
/ T
T
OUT
J
IN
D
IN
< +125°C
IN
+ 0.3V)
–
+ 0.3V)
10
V
R
6
–0.01
IN
Min
500
– 2.5% V
2.7
—
—
—
—
—
—
—
—
—
—
—
—
= V
IN
R
V
+ 1.0V, (Note 1), I
R
+ V
R
0.002
1200
0.05
0.05
0.04
Typ
200
350
260
± 0.5% V
† Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
40
20
60
80
64
—
—
DROPOUT
A
, T
R
and V
+0.01
J
1400
Max
0.35
L
+ 2.5%
130
390
650
130
,
6.0
30
—
—
—
—
—
1
= 100 µA, C
JA
IN
). Exceeding the maximum allowable power
2.7V for I
ppm/°C Note 3
nV/ Hz I
%/mA
Units
V/W
mA
mV
mA
µA
µA
db
%
V
V
L
© 2005 Microchip Technology Inc.
= 3.3 µF,
LMAX
L
Note 2
Note 1
(V
I
I
I
I
I
SHDN = V
SHDN = 0V
F
V
Note 6
= 0.1 mA to I
L
L
L
L
L
L
OUT
R
= 0.1 mA to I
= 100 µA
= 100 mA
= 300 mA
= 500 mA
= I
at V
1 kHz
+ 1V)
OUTMAX
= 0V
IN
Conditions
= 6V for T = 10 ms.
IH
V
, I
, F = 10 kH
OUTMAX
IN
L
OUTMAX
= 0
6V
.
Z