LT1761ES5-3.3#TR Linear Technology, LT1761ES5-3.3#TR Datasheet - Page 17
![IC LDO REG 100MA 3.3V TSOT23-5](/photos/6/57/65785/tsot-23-5_05-08-1635_sml.jpg)
LT1761ES5-3.3#TR
Manufacturer Part Number
LT1761ES5-3.3#TR
Description
IC LDO REG 100MA 3.3V TSOT23-5
Manufacturer
Linear Technology
Datasheet
1.LT1761ES5-3.3TRMPBF.pdf
(22 pages)
Specifications of LT1761ES5-3.3#TR
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 20V
Voltage - Dropout (typical)
0.3V @ 100mA
Number Of Regulators
1
Current - Output
100mA
Current - Limit (min)
110mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TSOT-23-5, TSOT-5, TSOP-5
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIONS INFORMATION
Voltage and temperature coeffi cients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or micro-
phone works. For a ceramic capacitor the stress can be
induced by vibrations in the system or thermal transients.
The resulting voltages produced can cause appreciable
amounts of noise, especially when a ceramic capacitor is
used for noise bypassing. A ceramic capacitor produced
Figure 5’s trace in response to light tapping from a pencil.
Similar vibration induced behavior can masquerade as
increased output voltage noise.
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
2. GND pin current multiplied by the input voltage:
Figure 5. Noise Resulting from Tapping on a Ceramic Capacitor
differential: (I
(I
500μV/DIV
GND
V
OUT
)(V
LT1761-5
C
C
I
IN
LOAD
OUT
BYP
).
= 0.01μF
= 10μF
= 100mA
OUT
)(V
IN
100ms/DIV
– V
OUT
), and
1761 F05
The ground pin current can be found by examining the
GND Pin Current curves in the Typical Performance Char-
acteristics section. Power dissipation will be equal to the
sum of the two components listed above.
The LT1761 series regulators have internal thermal limiting
designed to protect the device during overload conditions.
For continuous normal conditions, the maximum junction
temperature rating of 125°C must not be exceeded. It is
important to give careful consideration to all sources of
thermal resistance from junction to ambient. Additional
heat sources mounted nearby must also be considered.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
The following table lists thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32" FR-4 board with one ounce
copper.
Table 1. Measured Thermal Resistance
*Device is mounted on topside.
Calculating Junction Temperature
Example: Given an output voltage of 3.3V, an input voltage
range of 4V to 6V, an output current range of 0mA to 50mA
TOPSIDE*
2500mm
1000mm
225mm
100mm
50mm
COPPER AREA
2
2
2
2
2
BACKSIDE
2500mm
2500mm
2500mm
2500mm
2500mm
2
2
2
2
2
BOARD AREA
2500mm
2500mm
2500mm
2500mm
2500mm
LT1761 Series
2
2
2
2
2
(JUNCTION-TO-AMBIENT)
THERMAL RESISTANCE
125°C/W
125°C/W
130°C/W
135°C/W
150°C/W
17
1761sff