LT1086IM-3.3#TR Linear Technology, LT1086IM-3.3#TR Datasheet - Page 10
![IC REG LDO 1.5A POS 3.3V 3DD](/photos/12/61/126135/161-3-dd_sml.jpg)
LT1086IM-3.3#TR
Manufacturer Part Number
LT1086IM-3.3#TR
Description
IC REG LDO 1.5A POS 3.3V 3DD
Manufacturer
Linear Technology
Datasheet
1.LT1086CTPBF.pdf
(16 pages)
Specifications of LT1086IM-3.3#TR
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 20V
Voltage - Dropout (typical)
1.3V @ 1.5A
Number Of Regulators
1
Current - Limit (min)
1.5A
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
TO-263-2, D⊃2Pak (2 leads + Tab), TO-263AB
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIONS
LT1086 Series
Load Regulation
Because the LT1086 is a 3-terminal device, it is not
possible to provide true remote load sensing. Load regu-
lation will be limited by the resistance of the wire connect-
ing the regulator to the load. The data sheet specification
for load regulation is measured at the bottom of the
package. Negative side sensing is a true Kelvin connec-
tion, with the bottom of the output divider returned to the
negative side of the load. Although it may not be immedi-
ately obvious, best load regulation is obtained when the
top of the resistor divider R1 is connected directly to the
case not to the load , as illustrated in Figure 2. If R1 were
connected to the load, the effective resistance between the
regulator and the load would be:
Connected as shown, R
ratio. R
This translates to 4mV/ft at 1A load current, so it is
important to keep the positive lead between regulator and
load as short as possible and use large wire or PC board
traces.
Note that the resistance of the package leads for the H
package 0.06 /inch. While it is usually not possible to
connect the load directly to the package, it is possible to
connect larger wire or PC traces close to the case to avoid
voltage drops that will degrade load regulation.
For fixed voltage devices the top of R1 is internally Kelvin
connected and the ground pin can be used for negative
side sensing.
10
R
P
R2 + R1
V
P
Figure 2. Connections for Best Load Regulation
IN
is about 0.004 per foot using 16-gauge wire.
R1
IN
*CONNECT R1 TO CASE
CONNECT R2 TO LOAD
, R
LT1086
U
ADJ
P
= Parasitic Line Resistance
P
INFORMATION
OUT
U
is not multiplied by the divider
LINE RESISTANCE
PARASITIC
R2*
R1*
R
P
W
1086 • F02
U
R
L
Thermal Considerations
The LT1086 series of regulators have internal power and
thermal limiting circuitry designed to protect the device
under overload conditions. For continuous normal load
conditions however, maximum junction temperature rat-
ings must not be exceeded. It is important to give careful
consideration to all sources of thermal resistance from
junction to ambient. This includes junction-to-case, case-
to-heat sink interface and heat sink resistance itself. New
thermal resistance specifications have been developed to
more accurately reflect device temperature and ensure
safe operating temperatures. The data section for these
new regulators provides a separate thermal resistance and
maximum junction temperature for both the Control Sec-
tion and the Power Transistor . Previous regulators, with a
single junction-to-case thermal resistance specification,
used an average of the two values provided here and
therefore could allow excessive junction temperatures
under certain conditions of ambient temperature and heat
sink resistance. To avoid this possibility, calculations
should be made for both sections to ensure that both
thermal limits are met.
For example, using a LT1086CK (TO-3, Commercial) and
assuming:
Power dissipation under these conditions is equal to:
Junction temperature will be equal to:
For the Control Section:
For the Power Transistor:
V
T
thermal compound.
P
T
T
95 C < 125 C = T
Commercial Range)
T
103.8 C < 150 C = T
Commercial Range)
A
J
J
J
CASE-TO-HEAT SINK
IN
D
= 75 C 4W(3 C/W 0.2 C/ W 1.5 C/ W) = 94.6 C
= 75 C 4W(3 C/ W 0.2 C/ W 4 C/ W) = 103.8 C
= T
= 75 C,
(max continuous) = 9V, V
= (V
A
IN
P
– V
D
HEAT SINK
(
OUT
HEAT SINK
)(I
JMAX
= 0.2 C/ W for T package with
OUT
JMAX
= 3 C/W,
(Control Section
) = 4W
(Power Transistor
CASE-TO-HEAT SINK
OUT
= 5V, I
OUT
= 1A,
sn1086 1086ffs
+
JC
)