LT1764EQ-3.3#TR Linear Technology, LT1764EQ-3.3#TR Datasheet - Page 11
![IC REG LDO 3.3V 3A LN DDPAK-5](/photos/7/55/75544/161-5-dd_sml.jpg)
LT1764EQ-3.3#TR
Manufacturer Part Number
LT1764EQ-3.3#TR
Description
IC REG LDO 3.3V 3A LN DDPAK-5
Manufacturer
Linear Technology
Datasheet
1.LT1764EQ-2.5.pdf
(20 pages)
Specifications of LT1764EQ-3.3#TR
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 20V
Voltage - Dropout (typical)
0.34V @ 3A
Number Of Regulators
1
Current - Output
3A
Current - Limit (min)
3.1A
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-263-5, D²Pak (5 leads + Tab), TO-263BA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
The LT1764 series are 3A low dropout regulators opti-
mized for fast transient response. The devices are capable
of supplying 3A at a dropout voltage of 340mV. The low
operating quiescent current (1mA) drops to less than 1µA
in shutdown. In addition to the low quiescent current, the
LT1764 regulators incorporate several protection features
which make them ideal for use in battery-powered sys-
tems. The devices are protected against both reverse input
and reverse output voltages. In battery backup applica-
tions where the output can be held up by a backup battery
when the input is pulled to ground, the LT1764-X acts like
it has a diode in series with its output and prevents reverse
current flow. Additionally, in dual supply applications
where the regulator load is returned to a negative supply,
the output can be pulled below ground by as much as 20V
and still allow the device to start and operate.
Adjustable Operation
The adjustable version of the LT1764 has an output
voltage range of 1.21V to 20V. The output voltage is set by
the ratio of two external resistors as shown in Figure 2. The
device servos the output to maintain the voltage at the ADJ
pin at 1.21V referenced to ground. The current in R1 is
then equal to 1.21V/R1 and the current in R2 is the current
in R1 plus the ADJ pin bias current. The ADJ pin bias
current, 3µA at 25°C, flows through R2 into the ADJ pin.
The output voltage can be calculated using the formula in
Figure 2. The value of R1 should be less than 4.17k to
minimize errors in the output voltage caused by the ADJ
pin bias current. Note that in shutdown the output is turned
off and the divider current will be zero.
The adjustable device is tested and specified with the ADJ
pin tied to the OUT pin for an output voltage of 1.21V.
Specifications for output voltages greater than 1.21V will
V
IN
IN
LT1764
GND
OUT
ADJ
Figure 2. Adjustable Operation
U
R2
R1
1764 F02
+
U
V
OUT
V
V
I
OUTPUT RANGE = 1.21V TO 20V
ADJ
OUT
ADJ
W
=
=
=
3
1 21
1 21 1
µ AT 25 C
.
.
A
V
V
⎛
⎜
⎝
+
°
R
R
2
1
U
⎞
⎟ +
⎠
(
I
ADJ
)( )
R
2
be proportional to the ratio of the desired output voltage to
1.21V: V
output current change of 1mA to 3A is – 3mV typical at
V
Output Capacitance and Transient Response
The LT1764 regulators are designed to be stable with a
wide range of output capacitors. The ESR of the output
capacitor affects stability, most notably with small capaci-
tors. A minimum output capacitor of 10µF with an ESR in
the range of 50mΩ to 3Ω is recommended to prevent
oscillations. Larger values of output capacitance can de-
crease the peak deviations and provide improved transi-
ent response for larger load current changes. Bypass
capacitors, used to decouple individual components pow-
ered by the LT1764-X, will increase the effective output
capacitor value.
Extra consideration must be given to the use of ceramic
capacitors. Ceramic capacitors are manufactured with a
variety of dielectrics, each with different behavior across
temperature and applied voltage. The most common di-
electrics used are specified with EIA temperature charac-
teristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V
dielectrics are good for providing high capacitances in a
small package, but they tend to have strong voltage and
temperature coefficients as shown in Figures 3 and 4.
When used with a 5V regulator, a 16V 10µF Y5V capacitor
can exhibit an effective value as low as 1µF to 2µF for the
DC bias voltage applied and over the operating tempera-
ture range. The X5R and X7R dielectrics result in more
stable characteristics and are more suitable for use as the
output capacitor. The X7R type has better stability across
temperature, while the X5R is less expensive and is
available in higher values. Care still must be exercised
when using X5R and X7R capacitors; the X5R and X7R
codes only specify operating temperature range and maxi-
mum capacitance change over temperature. Capacitance
change due to DC bias with X5R and X7R capacitors is
better than Y5V and Z5U capacitors, but can still be
significant enough to drop capacitor values below appro-
priate levels. Capacitor DC bias characteristics tend to
improve as component case size increases, but expected
capacitance at operating voltage should be verified.
OUT
(5V/1.21V)(–3mV) = – 12.4mV
= 1.21V. At V
OUT
/1.21V. For example, load regulation for an
OUT
= 5V, load regulation is:
LT1764 Series
11
1764fb